00190725-01.pdf - 第32页
3.4 Prer equi sites f or M S-10 2, MS-12 8 an d MS -132 3.4. 1 Syst em Req uirem ents • Winchester • Interf ace Software V 2.5 and higher • Station Software from MSX.200.xxx • Axis Car d Software Ver sion 2.5 and higher …
3.3 Prerequisites for HS-180 Adhesive Application Station II
3.3.1 System Requirements
• Computer, series 362 with one HD disk drive or
• Computer 200 with DD or HD disk drive or
• Computer 310, 332 with HD twin floppy disk drive or DD disk drive
• HS-180 Interface Software Version 2.3 and higher,
• Line/Station Software from Version 2.01 (see following NOTE) *
• Axis Card Software Version 1.8 and higher
• BASIC from V5.0
*
The version to be used is selected by the operator in the Machine Selection Menu
NOTE:
Adhesive Station
I cannot
be measured with the AutoCal program!
The new HP printer requires the use of BASIC Version 6.21.
This version is delivered along with the AutoCal program (see Chapter 4, "Set of Diskettes").
If the
LRB <102.xxx version
is still used on the line computer, please order an update!
3.3.2 Testing Aids
• AutoCal program, available on 2 different sets of diskettes:
—
AutoCal program on 5 DD diskettes, item no. 00322032
—
AutoCal program on 4 DD diskettes and 1 HD diskette, item no. 00322032
(For details please refer to chapter 4. Supply source see page 3-2)
NOTE
The following testing aids must be available for the performance of the Routine Check (all measuring rou-
tines are carried out). For individual checks, only the testing aids listed in chapter 8 are required.
The following testing aids are delivered with the machine:
• MA-zero point insert for adhesive station II, item no. 02102407
Parts to be ordered:
• New MA-zero point gauge (with 2 holes: ∅ 3.5 mm and ∅ 5 mm), item no. 00120060
1)
• Glass mapping plate, included in the Glass Mapping Case, item no.: upon request.
1)
Only
one
MA-zero point gauge is required for calibrating
all
stations of
all
lines!
Additionally required testing aids:
• Plasticine
A work diskette must also be provided
• BASIC line computer: One blank HP formatted 3.5" diskette, write protection tab deactivated.
User’s Manual AutoCal Program 3 Requirements for Use
Softwareversion 114.xxx 3.3 Prerequisites for HS-180 Adhesive Application Station II
3 - 3
3.4 Prerequisites for MS-102, MS-128 and MS-132
3.4.1 System Requirements
• Winchester
• Interface Software V 2.5 and higher
• Station Software from MSX.200.xxx
• Axis Card Software Version 2.5 and higher
• BASIC from version 6.0 (contained on the hard disk/Winchester)
NOTE:
The new HP printer requires the use of BASIC Version 6.21.
This version is delivered along with the AutoCal program (see chapter 4, "Set of Diskettes").
3.4.2 Testing Aids Required
• AutoCal program, available on 2 different sets of diskettes:
—
AutoCal program on 5 DD diskettes, item no. 00322032
—
AutoCal program on 4 DD diskettes and 1 HD diskette, item no. 00322032
(For details refer to chapter 4. Supply source - see below)
NOTE
The following testing aids must be available for the performance of the Routine Check (all measuring rou-
tines are carried out). For individual checks, only the testing aids listed in chapter 9 are required.
The following testing aid are delivered along with the machine:
• Steel nozzle, type 104, item no. 00301435
• New MA-zero point gauge (with 2 holes: ∅ 3.5 mm and ∅ 5 mm), item no. 00120060
• New adjusting gauge for component table ("iron", with 2 holes), item no. 00120040
• Adjusting gauge for adhesive application head, with tip, item no. 00310314
• Teach panel, external, item no. 00132207
• Calibrating nozzle for coplanarity module, item no. 00301711
• VISION 2 Calibration plate, item no. 00132070
• 2 Test sockets for nozzle changer
*)
:
Large test socket (for special holder), item no. 00311659
Small test socket (for normal holder), item no. 02102021
• Nozzle top part = nozzle insert, item no. 00302566
*)
*) also included with nozzle changer accessories kit
Parts to be ordered:
• Nozzle adapter, type 117, item no. 00300659
• Mapping plate and centering square for MS-102/128, contained in the Mapping Case, item no. 00132040
• Mapping plate and centering square for MS-132, contained in the Mapping Case, item no. 00134100
3 Requirements for Use User’s Manual AutoCal Program
3.4 Prerequisites for MS-102, MS-128 and MS-132 Softwareversion 114.xxx
3 - 4
Additionally required testing aids:
• Plasticine
Supply source: Siemens AG
AUT 5 V Service
Rupert-Mayer-Str. 44
D-81359 München
Tel. 089/722 61200
FAX: 089/722 24260
User’s Manual AutoCal Program 3 Requirements for Use
Softwareversion 114.xxx 3.4 Prerequisites for MS-102, MS-128 and MS-132
3 - 5