00190725-01.pdf - 第34页

T his page intentionally left blank! 3 Req ui rem en ts fo r Us e Use r’ s Ma nual A utoCa l Pro gra m 3.4 Prerequisites for MS-102, M S-128 an d MS-132 Softwareversi on 114.xxx 3 - 6

Additionally required testing aids:

• Plasticine

Supply source: Siemens AG

AUT 5 V Service

Rupert-Mayer-Str. 44

D-81359 München

Tel. 089/722 61200

FAX: 089/722 24260

User’s Manual AutoCal Program 3 Requirements for Use

Softwareversion 114.xxx 3.4 Prerequisites for MS-102, MS-128 and MS-132

3 - 5

This page intentionally left blank!

3 Requirements for Use User’s Manual AutoCal Program

3.4 Prerequisites for MS-102, MS-128 and MS-132 Softwareversion 114.xxx

3 - 6

4 Preparatory Work to be Performed Before (up to and

including) the Start of the Calibration Procedure

The following work must be performed before calibration of your machine can be performed:

1.

Select the correct set of diskettes and determine which type of HP printer is used (Think-Jet / Desk-Jet).

2.

Check the MA-data before copying (e.g. activation of the installed options).

3.

Copy the MA-data to the work diskette (for the calibration of HS-180 Placement Stations and Adhesive Station II).

4.

Install the program including the printer driver on the hard disk (where a hard disk is available with sufficient

storage space).

5.

Perform a final check to ensure all starting prerequisites are fulfilled.

6.

Call up/start the program from the hard disk or from the diskette.

NOTE

If the station computer (HS) or the MS machine computer works runs on BASIC Version 5.0, the AutoCal

program should always be started from diskette. The same applies if computer 300 is only equipped

with a LIF-formatted 10MB or 20MB hard disk, or if there is not sufficient storage space on the hard disk.

➤ All of the above steps are described in this chapter in the same sequence as indicated.

4.1 Sets of Diskettes / Handling of Diskettes

AutoCal program version 114.xxx is delivered on 2 different sets of diskettes.

4.1.1 Designation and Contents of the Diskettes

Set of DD diskettes, comprising 5 DD diskettes:

• Start diskette : BASIC operating system and AUTOST program

• Installation diskette 1 : AutoCal program and Think-Jet printer drivers

• Installation diskette 2 : machine-specific modules

• Printer driver diskette 1 : printer driver for Think-Jet printer at the HPIP bus (DST.001.006)

• Printer driver diskette 2 : Printer driver for Desk-Jet printer at the parallel bus (DST.001.006)

Set of HD diskettes, comprising 4 DD diskettes and 1 HD diskette:

• Start diskette (DD) : BASIC operating system and AUTOST program

• Installation diskette 1 (1+2, HD): complete AutoCal program and Think-Jet printer driver

• Printer driver diskette 1 (DD) : printer driver for Think-Jet printer at HPIP bus (DST.001.006)

• Printer driver diskette 2 (DD) : printer driver for Desk-Jet printer at parallel bus (DST.001.006)

NOTE

If the Desk-Jet printer is used, BASIC Version 6.21 must be installed on all computers that are equipped with

a hard disk. This version is supplied from LC-BASIC version 209 and SRHx 225 onwards, as well as from MS-

version 206. If the wrong BASIC version is installed on the computer, error 12 is signaled during the print-out.

User’s Manual AutoCal Program 4 Preparatory Work to be Performed Before (up to and including) the Start of the Calibration Procedure

Software Version 114.xxx 4.1 Sets of Diskettes / Handling of Diskettes

4 - 1