52986207.pdf - 第5页
第 iii 页，共 iv 页 Radial 机器调校指南 52986207 修订版 A 本文档支持 Radial 机器。 N 型砧刀原点顶柱调整 .......... .............. .............. .............. .............. .............. ......122 剪脚器归零 ................. .............. ............…
本文档支持 Radial 机器。
第
ii
页，共
iv
页
52986207 修订版 A Radial 机器调校指南
插件头对中调整 ........................................................................................................56
元件传送组件调校 （初步）....................................................................................61
CTA 下导块高度调整 ...............................................................................................61
CTA 弹簧闩锁高度调整 ...........................................................................................62
CTA 链夹支座调整 ...................................................................................................63
CTA 上导块调整 .......................................................................................................64
定位系统调校 ............................................................................................................66
转盘对正调整 ............................................................................................................66
插件头驱动组件调校 ................................................................................................70
插件头 Theta 轴调校 .................................................................................................70
插件头组件安装 ........................................................................................................74
插件头垂直轴调校步骤 ............................................................................................75
推杆轴调校步骤 ........................................................................................................79
Theta 角度推杆轴校准 ..............................................................................................86
安装触发块夹具 ...................................................................................................86
执行 Theta 角度推杆轴校准 ................................................................................88
X 轴和 Y 轴调校 .......................................................................................................89
X 和 Y 轴编码器调整 ...............................................................................................89
X 和 Y 轴偏移量调整 ...............................................................................................92
元件传送组件调校 （最终）....................................................................................96
CTA 与插件头对正调整 ...........................................................................................96
链夹与 CTA 对正调整 ..............................................................................................98
闩锁同步调整 ..........................................................................................................100
CTA 对插件头冲程调整 .........................................................................................101
CTA 原点传感器调整 .............................................................................................104
设置步骤 .............................................................................................................104
调整步骤 .............................................................................................................105
验证步骤 .............................................................................................................107
凸块定位调整 ..........................................................................................................107
剪脚头调校 ..............................................................................................................109
VSL T 型剪脚头开口调整 ......................................................................................109
VSL T 型砧座到剪脚成型刀 （窗口开口）.....................................................110
VSL T 型剪脚成型刀冲程调整 .........................................................................113
VSL T 型中间剪脚成型刀冲程调整 .................................................................115
VSL T 型连续性间隙调整 .................................................................................116
N 型剪脚头调整 ......................................................................................................118
N 型剪脚成型刀冲程调整..................................................................................119
N 型连续性间隙调整..........................................................................................121
第
iii
页，共
iv
页
Radial 机器调校指南 52986207 修订版 A
本文档支持 Radial 机器。
N 型砧刀原点顶柱调整......................................................................................122
剪脚器归零 ..............................................................................................................123
剪脚器 Theta 轴调校 ...............................................................................................126
剪脚头与插件头组件对正 ......................................................................................130
安装剪脚头 ..............................................................................................................135
剪脚头高度调整 ......................................................................................................136
剪脚到位开关调整 ..................................................................................................138
BEC 调校 .................................................................................................................142
验证程序选项设置 ..................................................................................................142
调校机器 ..................................................................................................................143
BEC 调校 .................................................................................................................144
传感器初步调整 ......................................................................................................145
微调传感器 ..............................................................................................................146
建立传感器偏移量 ..................................................................................................147
送板系统：非旋转式 – LP 调校 ............................................................................149
传感器调整 ..............................................................................................................149
桥滑轨 （0HS、 1HS、 4HS、 5HS）..............................................................149
输出推杆 (2HS)...................................................................................................149
传送机构 （1LS、 2LS、 3LS）.......................................................................149
桥传感器调整 （1PS、 2PS、 5PS、 6PS）.....................................................149
灵敏度调整 .........................................................................................................150
位置调整 .............................................................................................................150
自左至右传送方向.........................................................................................150
自右至左传送方向.........................................................................................151
自左至右和自右至左传送.............................................................................152
板定位调整 (9PS) ...............................................................................................153
气动调校 ..................................................................................................................154
调整桥升 / 降同步 ...................................................................................................154
调整传送伸出慢速 ..................................................................................................157
调整传送伸出快速同步 ..........................................................................................158
运行 BHS （送板系统）并测量总时间 ................................................................161
输出推杆组件 ..........................................................................................................162
本修订版的更改项 ..................................................................................................163
本文档支持 Radial 机器。
第
iv
页，共
iv
页
52986207 修订版 A Radial 机器调校指南