Chapter3_Repair_Guide.pdf - 第228页
Model DECAN Series Company SAMSUNG TECHWIN Module 3.12 MMI V ersion 01 Tit le MMI IO CHECK(OUTP UT) Page 3-12-6 Note No. 项目 标准值 1 PLACE STOPPER #1 UP 100~130msec 2 PLACE STOPPER #1 DOWN 100~130msec 3 BACKUP T ABLE#1 UP 3…
Model
DECAN Series
Company
SAMSUNG TECHWIN
Module
3.12 MMI
Version
01
Title
MMI IO CHECK(OUTPUT)
Page
3-12-5
Note
[MMI IO CHECK(OUTPUT)]
确认前/后面安装制动器上/下启动
点击 IO 窗口的<前/后面安装制动器上/下>，确认启动及输入信号感应
确认前/后面安装 BUT 上/下启动
点击 IO 窗口的<前/后面安装 BUT 上/下>，确认启动及输入信号感应
确认 ANC #1,#2 SOL 启动
点击 IO 窗口的<ANC#1,#2>，确认启动及输入信号感应
确认 Speed Control 启动
点击 IO 窗口的<Sys.Setup>→ <I/O>→ <Cylinder Check>，点击<Automatic>，将 Speed Controll
er 调整为符合于其结果值
Model
DECAN Series
Company
SAMSUNG TECHWIN
Module
3.12 MMI
Version
01
Title
MMI IO CHECK(OUTPUT)
Page
3-12-6
Note
No.
项目 标准值
1 PLACE STOPPER #1 UP 100~130msec
2 PLACE STOPPER #1 DOWN 100~130msec
3 BACKUP TABLE#1 UP 320±10msec
4 BACKUP TABLE #1 DOWN 95±25mSec
5 PLACE STOPPER #2 UP 80~110msec
6 PLACE STOPPER #2 DOWN 80~110msec
7 BACKUP TABLE #2 UP 320±10msec
8 BACKUP TABLE #2 DOWN 95±25mSec
9 ANC SHUTTER #1 CLOSE 60±10mSec
10 ANC SHUTTER #1 OPEN 40~50msec
11 ANC SHUTTER #2 CLOSE 60±10mSec
12 ANC SHUTTER #2 OPEN 40~50msec
确认前/后面 Edge Fixer 启动
点击 I/O 窗口的<前/后面安装边缘固定器前/后>，确认是否启动
Model
DECAN Series
Company
SAMSUNG TECHWIN
Module
3.12 MMI
Version
01
Title
MMI IO CHECK(OUTPUT)
Page
3-12-7
Note
确认入口/出口制动器启动
点击 I/O 窗口的<入口/出口制动器前/后>，确认是否启动
确认 OP Panel Lamp
各点击 IO 窗口的<READY>、<START>、<STOP>、<前/后 FEEDER CHANGE>、<RESET>按
钮，确认 OP Panel 的 Lamp 亮灯
确认 Tower Lamp
按照 I/O 窗口的<红色>、<黄色>、<绿色>蜂鸣器点击，确认 Tower Lamp 的亮灯及蜂鸣器
点击 OP PANEL 的<EMERGENGY>按钮，确认 Tower Lamp 的蜂鸣器及红灯闪烁状况