EUKYX-199-2100_G5S2_Instruction_Vol2_E.pdf - 第73页

EUKYX 1-23 199-2100 4.1 "Run Mode" T ab Sheet 4. 1 . 2 "Run Mode " Window ( " W a rm St ar t " Po ssible ) When the mach ine is set in the "P AU SE" mode duri ng the aut omati c op…

EUKYX

1-22199-2100

4.1 "Run Mode" Tab Sheet

Starting Procedure for Semi-Auto Step Any Desig (free designation)

(1) Transfer the PCB to the designated table.

Transfer the PCB manually to the aimed position.

(2) Designate the step in the "Any step designation" window and press the [Apply] button.

A dialogue "Do you save the change?" will be displayed. Select "Yes". After the selection, the

No. of designated steps is changed.

(3) Press the [Return] button to return to the "Semi-Auto Any Desig" window.

(4) When the [START] button on the operation panel is pressed, the designated step mounting

is started.

(a) Precautions during the step operation designated in “Any Step Designation” mode

• The addition or deletion of step operation designated in the “Any Step Designation”

mode, is disabled. Before or after the component placement, or after all applied steps

are cancelled in the case of stop in the course of the operation, such addition or deletion

is enabled.

• In the case that the step designated in “Any Step Designation” mode, is stopped in the

course of the operation and the placement is started again, the operation is started from

the head of the undone steps.

• In the case that the operation is to be started again, after the step designated in the “Any

Step Designation” mode, is stopped in the course of the operation and undone steps are

cleared, the operation is started from the head of the applied steps designated in “Any

Step Designation” mode.

• Even when the PCB is discharged after the operation is stopped in the course, the

operated step data is not cleared.

(b) After all the steps are performed

When the operation start is attempted after all the previously set steps are performed,

the component placement is not started. In order to start the component placement, clear

the previously set placement steps.

(1) Press the “Placement step clear” button on the “Semi-Auto Any Desig” window.

(2) Press the “Release all step” button on the “Any step designation” window and

press the “Apply” button.

(d) PCB Discharge

•

Discharge the PCB manually after all the steps designated in “Any Step Designation”

mode, are completed (including the stop in the course of the operation).

•

Start the normal operation after the PCB discharge.

Procedure

Note

Procedure

EUKYX

1-23199-2100

4.1 "Run Mode" Tab Sheet

4.1.2 "Run Mode" Window ("Warm Start" Possible)

When the machine is set in the "PAUSE" mode during the automatic operation, a warm start

operation becomes possible and the "Warm Start" window appears.

[1]

[2]

F2A21

[1] [Last Plc Pos Move] Button

When this button is pressed, the "Last Placement Point Check" window is opened.

[2] [Cancel Warm Start] Button

When pressed, the warm start is cancelled.

This button is displayed only in the window for the Supervisor. When the Warm start has been

stopped, the PCB is discharged without placing any component in the re-start operation. Pay

attention to it.

Refer to “5.3 Resumption of Production through Warm Start Procedure”

(Chapter 3 in Volume 1) for the detailed information on how to execute a warm start operation.

Note

Reference

EUKYX

1-24199-2100

4.1 "Run Mode" Tab Sheet

4.1.3 "Run Mode" Window in "Placement Recovery Available" Mode

"Enable" or "Disable" for the NL-axis Origin Teaching, is setup in this data box.

[1]

[2]

F2A22

[1] [Plc Pos Move] Button

When pressed, this button opens the "When the NL-axis origin teaching is to be performed, the

teaching time interval is selected from the following items." window.

A pre-pick nozzle conﬁrmation error will not occur when the pre-pick nozzle conﬁrmation

function is not used.

Refer to”4.2 “Opr.Mode” Tab Sheet” in "Chapter 1" for how to use the pre-pick nozzle

conﬁrmation function.

When the machine is reset to its normal condition from the "ERROR" window after a pre-pick

nozzle conﬁrmation error has occurred, the "Placement Step Recovery" window appears

automatically.

[2] [Cancel Place Rcvry] Button

When pressed, the placement recovery is cancelled.

Reference

Note