X3_X4_Series machine.pdf - 第27页

User manual SIPLAC E X-Series 2 Operational safety Software Version SR.601.xx 11/2005 US Edition 2.1 Safety instructions 27 2 Operational safety 2.1 Safety instructions 2.1.1 Convent ions for the use of hazard symbols Th…

1 Introduction User manual SIPLACE X-Series

1.9 Abbreviations Software Version SR.601.xx 11/2005 US Edition

1.9 Abbreviations

C&P Collect&Place

C&P12 Collect&Place head with 12 segments

C&P20 Collect&Place head with 20 segments

C&P6 Collect&Place head with 6 segments

CO Component

DC Dual conveyor

DCA Direct chip attach

EDIF Energy and data interface

EMR End of measuring range

ESD Electrostatically-sensitive group of components

ESD Electrostatic sensitive device

FC Flip chip

GND Ground

IC Integrated circuit

MC Machine controller

MMR Middle of measuring range

MTC Matrix tray changer

OSC Odd shaped components

P&P Pick&Place

PA Placement area

PCB Printed circuit board

SC Single conveyor

SC Station computer

SM Dual conveyor in Single conveyor mode

SMD Surface mounted device

SMR Start of measuring range

TH TwinHead

VS Vision system

WLAN Wireless Local Network

WT Waffle-pack tray

WTC Waffle-pack tray carrier

User manual SIPLACE X-Series 2 Operational safety

Software Version SR.601.xx 11/2005 US Edition 2.1 Safety instructions

2 Operational safety

2.1 Safety instructions

2.1.1 Conventions for the use of hazard symbols

This User Manual contains notes that must be observed to guarantee your personal safety and to

avoid damage to equipment. These notes are highlighted by warning triangles and are indicated

as follows according to the level of risk:

DANGER or

as used in this User Manual means that death, severe injury or considerable damage to equip-

ment

will

occur if the danger instructions are not followed.

WARNING or

as used in this User Manual means that death, severe injury or considerable damage to equip-

ment

may

occur if the warning instructions are not followed.

CAUTION or

as used in this User Manual means that slight injury or damage to equipment may occur if the cau-

tion instructions are not followed.

PLEASE NOTE

as used in this User Manual provides information on the product or indicates a part of the User

Manual that requires particular attention.

2.1.2 Qualified personnel

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and preventive maintenance of automatic placement systems and add-on devices and

are suitably qualified, e.g.

– have been trained, instructed or authorized to switch on and off, isolate, earth and identify

electrical circuits and system components in accordance with normal safety standards.

– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-

cordance with normal safety standards.

– have received first aid training.

2 Operational safety User manual SIPLACE X-Series

2.1 Safety instructions Software Version SR.601.xx 11/2005 US Edition

2.1.3 Use as prescribed

The product must only be used for its intended purposes as described in the catalogs and techni-

cal descriptions, namely the placement of SMD components, and only with the third-party equip-

ment and components recommended or permitted by SIEMENS A&D. Use for a different or

extended purpose is not prescribed.

If the product is not used as prescribed, SIEMENS accepts no liability for any damage that may

occur and does not guarantee that the components will work properly and without problems.

Use as prescribed also includes compliance with all the instructions in the user manual.

For the product to operate correctly and reliably, it must have been transported, stored, erected

and assembled correctly and must be operated and maintained with care.

2.1.4 Failure to use as prescribed

Failure to use the product as prescribed can result in both danger to life and limb and material

damage. For this reason any use that is not prescribed is not allowed. If the product is not used

as prescribed, SIEMENS accepts no liability for any damage that may occur and does not guar-

antee that the components will work properly and without problems.

Failure to use the placement machine as prescribed includes, for example

– operation of the placement machine with safety equipment deactivated or removed.

– placement of components that do not meet the permitted specification.

– use of component feeder modules that have not been approved.

– use of unauthorized accessories and additional modules.

– use of the placement machine by unqualified personnel.

– operation of the placement machine without the hand guard (dummy feeder module) if not

every location is occupied with a feeder module or if a waffle-pack tray holder is used.

– unclear allocation of electrical connecting cables to each placement machine and the in-

stalled options (e.g. MTC, productivity lift, vacuum pump).

– if there are two or more people standing at a component trolley location at the same time dur-

ing the retrofit.