X3_X4_Series machine.pdf - 第28页

2 Operational safety User manual SIPLACE X-Series 2.1 Safety instr uctions Software Version SR.601.xx 11/2005 US E dition 28 2.1. 3 Use as pres cribe d The pr oduct m ust o nly be used fo r its i ntended purpos es as des…

User manual SIPLACE X-Series 2 Operational safety

Software Version SR.601.xx 11/2005 US Edition 2.1 Safety instructions

2 Operational safety

2.1 Safety instructions

2.1.1 Conventions for the use of hazard symbols

This User Manual contains notes that must be observed to guarantee your personal safety and to

avoid damage to equipment. These notes are highlighted by warning triangles and are indicated

as follows according to the level of risk:

DANGER or

as used in this User Manual means that death, severe injury or considerable damage to equip-

ment

will

occur if the danger instructions are not followed.

WARNING or

as used in this User Manual means that death, severe injury or considerable damage to equip-

ment

may

occur if the warning instructions are not followed.

CAUTION or

as used in this User Manual means that slight injury or damage to equipment may occur if the cau-

tion instructions are not followed.

PLEASE NOTE

as used in this User Manual provides information on the product or indicates a part of the User

Manual that requires particular attention.

2.1.2 Qualified personnel

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and preventive maintenance of automatic placement systems and add-on devices and

are suitably qualified, e.g.

– have been trained, instructed or authorized to switch on and off, isolate, earth and identify

electrical circuits and system components in accordance with normal safety standards.

– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-

cordance with normal safety standards.

– have received first aid training.

2 Operational safety User manual SIPLACE X-Series

2.1 Safety instructions Software Version SR.601.xx 11/2005 US Edition

2.1.3 Use as prescribed

The product must only be used for its intended purposes as described in the catalogs and techni-

cal descriptions, namely the placement of SMD components, and only with the third-party equip-

ment and components recommended or permitted by SIEMENS A&D. Use for a different or

extended purpose is not prescribed.

If the product is not used as prescribed, SIEMENS accepts no liability for any damage that may

occur and does not guarantee that the components will work properly and without problems.

Use as prescribed also includes compliance with all the instructions in the user manual.

For the product to operate correctly and reliably, it must have been transported, stored, erected

and assembled correctly and must be operated and maintained with care.

2.1.4 Failure to use as prescribed

Failure to use the product as prescribed can result in both danger to life and limb and material

damage. For this reason any use that is not prescribed is not allowed. If the product is not used

as prescribed, SIEMENS accepts no liability for any damage that may occur and does not guar-

antee that the components will work properly and without problems.

Failure to use the placement machine as prescribed includes, for example

– operation of the placement machine with safety equipment deactivated or removed.

– placement of components that do not meet the permitted specification.

– use of component feeder modules that have not been approved.

– use of unauthorized accessories and additional modules.

– use of the placement machine by unqualified personnel.

– operation of the placement machine without the hand guard (dummy feeder module) if not

every location is occupied with a feeder module or if a waffle-pack tray holder is used.

– unclear allocation of electrical connecting cables to each placement machine and the in-

stalled options (e.g. MTC, productivity lift, vacuum pump).

– if there are two or more people standing at a component trolley location at the same time dur-

ing the retrofit.

User manual SIPLACE X-Series 2 Operational safety

Software Version SR.601.xx 11/2005 US Edition 2.1 Safety instructions

2.1.5 Important notes on operational safety

The following points MUST be observed in order to maintain operational safety:

2.1.5.1 General

Æ The operational safety of SMD automatic placement systems can be guaranteed only if the

system is used as prescribed and in accordance with the instructions in the User/Service

Manuals.

Æ Always follow any safety regulations specific to your country.

Æ Make sure that the warning labels are always clearly identifiable and always easily readable.

Æ Replace any damaged warning or notice labels. Replace any labels that are missing.

Æ The machine key for releasing the covers on the machine must be kept in a safe place where

it is only accessible to qualified personnel.

PLEASE NOTE

The machine owner, and only the machine owner, is responsible for the safekeeping of the

machine key and for ensuring that it is handed over to authorized persons. 2

Æ If it is necessary to work on the machine and you do not have adequately trained personnel

within your operation, always call in a SIEMENS service engineer. SIEMENS will not accept

liability for any damage or consequential damage that is the result of incorrect work.

Æ If particularly hazardous situations are identified while the machine is in use, the machine

owner must immediately notify the manufacturer in writing so that appropriate action can be

taken to reduce the potential danger.

WARNING

In spite of all the safety precautions taken by the manufacturer, failure to use the system as pre-

scribed can result in severe physical injury (e.g. from the moving gantry or lifting table) and/or con-

siderable damage to equipment. For the machine to be safe, it must be used correctly by qualified

personnel and all warnings must be observed. Some work on the machine (e.g. setting up) re-

quires training that goes beyond the scope of this Manual. 2