X3_X4_Series machine.pdf - 第355页
User manual SIPLAC E X-Series 6 Component han dling Software Vers ion SR.601.xx 11/2005 US Edition 6.7 SIPLACE HF component trolleys 355 6 6.7.3 Dimensions and center of gravity of the SIPLACE HF component trolley 6 Fig.…
6 Component handling User manual SIPLACE X-Series
6.7 SIPLACE HF component trolleys Software Version SR.601.xx 11/2005 US Edition
354
Description of the modules 6
The chassis (item 1) runs smoothly and is easy to maneuver.
The handles (item 7) can be folded up or down.
The component table (item 2) has a capacity of up to 15 locations for 30 mm wide feeder modules.
The feeder modules are mechanically centered on the table using centering pins and centering
balls. The feeder modules are supplied with compressed air via a separate compressed air bar.
The interface for the power module, communication and safety circuits (item 6) is beneath the
component feeder table bed. The compressed air supply for bulk case feeder modules also
passes via this interface.
NOTE ON OPERATIONAL SAFETY
All component trolleys or matrix tray changers must be docked on the machine in order to oper-
ate it. If they are not, the machine stays in emergency stop status. The placement process is
interrupted.
The communication interface (item 3) supplies the necessary voltages and control signals to the
feeder modules.
In the standard version, the tape reel container (item 4) holds tape reels up to 17" (432 mm). The
pull-out waste tape container (item 5) can be found beneath the chassis. The cut waste tape travel
down a chute into the waste container, which must be regularly emptied.
6.7.2 Technical data, SIPLACE HF component trolleys
6
Length x width
727.5 x 592 mm²
751.5 x 592 mm² with waste container
Height
829.5 mm for 830 mm PCB transport height
899.5 mm for 900 mm PCB transport height
929.5 mm for 930 mm PCB transport height
949.5 mm for 950 mm PCB transport height
PCB transport height
830 mm ± 15 mm (standard)
900 mm ± 15 mm (SMEMA)
930 mm ± 15 mm (SMEMA)
950 mm ± 15 mm (SMEMA)
Weight
Without feeder modules
With feeder module at all locations
With compressed air supply for bulk case
feeder modules and adapter for 3rd tape reel
Approx. 85 kg
Approx. 125 kg
Approx. 150 kg
User manual SIPLACE X-Series 6 Component handling
Software Version SR.601.xx 11/2005 US Edition 6.7 SIPLACE HF component trolleys
355
6
6.7.3 Dimensions and center of gravity of the SIPLACE HF component trolley
6
Fig. 6.7 - 4 Dimensions of the component trolley, SIPLACE HF, all dimensions in
The center of gravity (A) of the component trolley was determined under the following conditions:
– Component trolley set to a PCB transport height of 830 mm.
Reel diameter
Standard
Maximum
Up to 432 mm (17")
483 mm (19")
Feeder module locations Max. 15
Changeover time for the component trolley Less than 1 min.
6 Component handling User manual SIPLACE X-Series
6.7 SIPLACE HF component trolleys Software Version SR.601.xx 11/2005 US Edition
356
6.7.4 SIPLACE HF tape container
The tape container can hold reels up to 19" in diameter. You should use spindles to process reels
of 15" diameter or more. The use of separating plates is described in section 5.3
on page 251.
PLEASE NOTE
For optimum operation, we recommend the use of spindles for 15" diameter or more.
Fig. 6.7 - 5 SIPLACE HF component trolley with tape container
(1) Component trolley
(2) Position of the spindles
(3) Waste tape container
(4) Tape container
(5) Separating plate
(6) Spindle (enlarged)