X3_X4_Series machine.pdf - 第356页

6 Component handling User manual SIPLACE X-Series 6.7 SIPLACE HF component trolleys Software Version SR.601.xx 11/2005 US E dition 356 6.7.4 SIPLACE HF t ape cont ainer The tape co ntainer can hold r eels up to 19" …

User manual SIPLACE X-Series 6 Component handling

Software Version SR.601.xx 11/2005 US Edition 6.7 SIPLACE HF component trolleys

355

6.7.3 Dimensions and center of gravity of the SIPLACE HF component trolley

Fig. 6.7 - 4 Dimensions of the component trolley, SIPLACE HF, all dimensions in

The center of gravity (A) of the component trolley was determined under the following conditions:

– Component trolley set to a PCB transport height of 830 mm.

Reel diameter

Standard

Maximum

Up to 432 mm (17")

483 mm (19")

Feeder module locations Max. 15

Changeover time for the component trolley Less than 1 min.

6 Component handling User manual SIPLACE X-Series

6.7 SIPLACE HF component trolleys Software Version SR.601.xx 11/2005 US Edition

356

6.7.4 SIPLACE HF tape container

The tape container can hold reels up to 19" in diameter. You should use spindles to process reels

of 15" diameter or more. The use of separating plates is described in section 5.3

on page 251.

PLEASE NOTE

For optimum operation, we recommend the use of spindles for 15" diameter or more.

Fig. 6.7 - 5 SIPLACE HF component trolley with tape container

(1) Component trolley

(2) Position of the spindles

(3) Waste tape container

(4) Tape container

(5) Separating plate

(6) Spindle (enlarged)

User manual SIPLACE X-Series 6 Component handling

Software Version SR.601.xx 11/2005 US Edition 6.7 SIPLACE HF component trolleys

357

6.7.4.1 Tape reel diameter in relation to the PCB transport height

6.7.5 External power supply for the SIPLACE HF component trolley

To keep the time required for a setup change as short as possible, component trolleys can be set

up in advance at a special external location. The feeder module functions and setting can be

checked there to prepare for use. We provide an external power supply for this purpose. It is used

to supply the component trolley with the required electrical power and compressed air.

6.7.5.1 Technical data

The kit contains a main power cable to European standards, a main power cable to US standards

and a connecting cable between the power supply and the component trolley.

6.7.6 Compressed air supply for bulk case feeder modules, SIPLACE HF

component trolley

Bulk case feeder modules require compressed air in order to work. A compressed air supply for

bulk case feeder modules is therefore available as an option.

It is easy to fit. First remove the sealing plug (item 1) from the compressed air connection on the

component feeder table (item 2). Then use two screws DIN 912, M8x20 (item 4) to fix the com-

pressed air supply (item 3) to the component feeder table (item 2). The compressed air supply has

retaining clips (item 5) on the back. They fix the bulk case feeder modules to the component table

and thus ensure a perfect compressed air supply.

Option – With support for 3rd tape reel

PCB conveyor height

of the component trolley

Tape reel diameter Tape reel diameter

830 mm 17" 15"

900 mm 19" 17"

930 mm 19" 17"

950 mm 19" 19"

Mains voltage 230 VAC ± 5 %

120 VAC ± 5 %

Compressed air connection Max. 1.0 MPa (10 bar)

Output pressure Can be regulated with a valve