X3_X4_Series machine.pdf - 第270页

5 Tasks on the machine User manual SIPLAC E X-Series 5.6 LCD and status displays on the X feeder m odule Software Version SR.601.xx 11/2005 US E dition 270 5 PLEAS E NOTE 5 Remove the componen t tape before a reference r…

User manual SIPLACE X-Series 5 Tasks on the machine

Software Version SR.601.xx 11/2005 US Edition 5.6 LCD and status displays on the X feeder module

269

5.6.1 Warnings

5.6.2 Error messages and trouble-shooting

Text on the

LCD display

Status

display

Meaning Trouble-shooting

Remove Foil Orange The selected function is not

permitted when the cover foil

is tensioned (foil rocker is

pressed down).

If you wish to carry out that function, remove

the foil from the pair of gear wheels and cut

it off to relieve the pressure on the foil rocker.

Text on the

LCD display

Status

display

Meaning Trouble-shooting

none Red,

flashing

Feeder module software not

jumping to the application

Reload the application software

Load feeder module software

Handle --->> Red Feeder module was sig-

naled, but removal handle is

not yet pushed in

Push in the removal handle

Low Voltage Orange 24V supply voltage did not

rise above the switch-on

threshold after switching on

Check the power supply

Low Voltage Red 24V supply voltage rose

above the switch-on thresh-

old after switching on and

was then interrupted

Check the power supply

Feed Timeout

TransTimeout

(Timeout in tape

feeder cycle)

Red Tape feeder cycle did not

end correctly within the spec-

ified time (timeout for the

"Feed" function)

Is the tape reel jammed in the container?

Is there a component jammed in the pick-up

area between component tape and compo-

nent window?

Once the obstacle has been eliminated, use

the arrow keys to restart the conveyor. The

feeder module will move the defective con-

veyor to the end, and then returned to its

position

Foil Torn Red Foil was not tensioned within

the specified time

The foil is probably torn. Insert new foil and

tension

Foil PeelErr Red Foil was not peeled off even

though the tape is moved

The cover foil is probably jammed beneath

the pick-up window and cannot be peeled

off correctly

5 Tasks on the machine User manual SIPLACE X-Series

5.6 LCD and status displays on the X feeder module Software Version SR.601.xx 11/2005 US Edition

270

PLEASE NOTE 5

Remove the component tape before a reference run.

Foil Jam Red Foil motor has locked up Leveling gears blocked by foil? => Remove

the foil

EEP-WriteErr

(Error while back-

ing up data in the

EEPROM)

Red The data back-up in the EE-

PROM was not carried out

correctly

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pick-up window).

Press the SET button to confirm the error.

Then press the yellow button to confirm the

reference run prompt.

EEP-ReadErr

(Error while read-

ing the EEPROM)

Red Data was not read from the

EEPROM correctly

EEP-DataErr

(Error while back-

ing up the data in

the EEPROM)

Red The data back-up in the EE-

PROM was not carried out

fully

Reference o Red Position information is no

longer available for the com-

ponent tape drive

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pick-up window).

Then press the "FOIL" button to start the

reference run.

CAN BusError Red CAN bus error Log off and on again, check the optical fiber

interface

ParNotSaved! Red Parameters were not saved Default parameters are loaded automatical-

ly, i.e. the most recent operator settings are

overwritten -> The settings (e.g. increment)

will have to be made again. Replace the

control board if this error occurs frequently.

ParWrongSave Red Wrong or incomplete param-

eters were saved

BootFlashErr

FlashDataErr

Red Can no longer write to boot

or application memory cor-

rectly

Replace the feeder module or control board

Text on the

LCD display

Status

display

Meaning Trouble-shooting

User manual SIPLACE X-Series 5 Tasks on the machine

Software Version SR.601.xx 11/2005 US Edition 5.7 Changing the set-up

271

5.7 Changing the set-up

5.7.1 Printing out the conversion instructions before changing the set-up

Before a change of set-up, print out the conversion instructions on the printer for the SIPLACE Pro

computer as described in the "SIPLACE Pro" manual or in the online help.

5.7.2 What you should note when changing the feeder modules

Handle the feeder modules carefully when you insert them into or remove them from the com-

ponent feeder table. Make sure that the X feeder modules do not bump against the centering

bar (see item 5 in Fig. 5.4 - 3

, page 260) on the component table.

Æ Vacuum the supporting surfaces of the feeder modules and clean the surface of the compo-

nent feeder table when necessary according to the instructions in the Preventive Mainte-

nance Manual.

Æ Remove loose components using a brush or a vacuum cleaner with a suitable nozzle.