00195193-02 SG D4 FSE en (1).pdf - 第198页
Gantry Settings Description of the PCB boards on the Gantry S tudent Guide SIPLACE D4 (FSE) Gantry EN 09/2006 184 8.2.3.2 V ision board (digit al) The Vision processor bo ard is mounted on the gantry he ad distributor bo…
Gantry
Description of the PCB boards on the Gantry Settings
Student Guide SIPLACE D4 (FSE)
EN 09/2006 Gantry
183
8.2.3.1.1 Description of LEDs on the Gantry Head Distributor
Legend PCB labeling LED status Description
1 1-WIRE Not in use
CAN-INT OFF not used
POWER-FAIL OFF Error +24 V power supply
(from the main machine)
2 DC-ER OFF Error DC/DC converter
DC-EN ON Enable DC/DC converter
+SP-ER OFF Error +5V track encoder
+SP-EN ON Enable +5V track encoder
+15-ER OFF Error +15V
-15-OK ON -15V is OK
3.3-EN ON Enable +3.3V digital
3.3-ER OFF Error +3.3V digital
+5V-EN ON Enable +5 V digital
+5V-ER OFF Error +5V digital
+AN-ER OFF Error analog supply C167
3 V-OK ON Internal voltage monitoring of
eSW
V-OK OFF
ERROR OFF Error eSW
TEST Toggle Timer eSW in operation
4 +V-LS ON OK + 15V light barrier
+V-LS OFF Error +15V light barrier
Z-O ON Z-axis is up
Z-U ON Z down has switched
ERR-ZH OFF Overload SM feed-in
ERR-DP OFF Overload SM rotary axis
ERR-BA OFF Overload SM reject
LS-ZH ON Light barrier SM feed-in
LS-DP ON Light barrier SM rotary axis
LS-BA ON Light barrier SM reject
Gantry
Settings Description of the PCB boards on the Gantry
Student Guide SIPLACE D4 (FSE)
Gantry EN 09/2006
184
8.2.3.2 Vision board (digital)
The Vision processor board is mounted on the gantry head distributor board. This PCB is used for all
four gantries.
8.2.3.3 CAN 16 bit Processor Board (TQ module)
The 16 BIT CAN processor is used for various different functions in the following units:
(see chapter communication and control too)
Visionboard, communication and control via the CAN Bus to the vision computer.
Gantry head distributor, control of head processes and vacuum
Legend:
1. X8 Connector illumination and video signals
PCB camera
2. X3 Connector illumination and video signals
component camera
3. LED‘s P15V - 15Volt / Vcc - Power supply
Vision board
4. DIP switch
5. CAN Prozessor 16 Bit (TQM Module)
6. Connector X22 - X24 Connectors for the video
cable to the trailing cable
NOTE:
The DIP switch configuration for gantry configuration is described in Section
8.2.4 Check the DIP Switches [J 184] .
Legend:
1. 7 Segment display
2. LED for manual RESET of processor
3. 16 Bit Processor
Gantry
Check the DIP Switches Settings
Student Guide SIPLACE D4 (FSE)
EN 09/2006 Gantry
185
Description of 7-segment display (normal operation "." flashes):
After switch ON the machine appears " 0 " on the display
Display "b" --> BIOS was started.
Display flashes alternatively between "b" and "." --> no application available or unable to start
application.
Display " -I " and " I- " application was loaded.
"." flashes on the display --> ready for operation.
8.2.4 Check the DIP Switches
8.2.4.1 DIP Switch on Gantry Head Distributor
Legend
DIP Switch
1 Gantry 1 3 Gantry 3
2 Gantry 2 4 Gantry 4
1 P0 – gantry ID0 address switch 1 --> gantry 5 Reset - CAN processor 16 Bit (TQM module)
2 P1 – gantry ID1 address switch 2 --> gantry 6 C0 – no current function
3 S1 – switch for DLM head (delay switching on
LB down – Z-axis)
7 C1 – no current function
4 BL – Enable boot loader for serial port 8 S2 – switch for DLM head (no current function)