00195193-02 SG D4 FSE en (1).pdf - 第277页

Modular conveyor Setting the fixed conveyor side (single and dual co nveyor) Conveyor Settings Student Guide SIPLACE D4 (FSE) EN 09/2006 Modular conveyor 261 1 1.3.2 Setting the fixed conveyor side (single and dual conve…

Modular conveyor

Conveyor Settings Adjusting the Tension of the Conveyor Toothed Belt

Student Guide SIPLACE D4 (FSE)

Modular conveyor EN 09/2006

260

11.3 - 1: Measuring and setting the belt tension for the width adjustment

Legend

1 Actuator fixing screw 4 Toothed drive belt for adjusting the width /

measuring the belt tension

2 Spindle with toothed wheel

3 Width adjustment stepping motor 5 Transport direction

The belt is tensioned by means of cams on the

idler pulleys. The idler pulleys are located on the

left and right of the motor.

Legend:

1. Loosen the cam shaft on the idler pulley and

set the belt tension.

NOTE:

The modular conveyor uses different belt lengths. The differing belt tensions

between the conveyor lanes are due to the different arrangement of hexagonal

shafts and deflection pulleys.

Modular conveyor

Setting the fixed conveyor side (single and dual conveyor) Conveyor Settings

Student Guide SIPLACE D4 (FSE)

EN 09/2006 Modular conveyor

261

11.3.2 Setting the fixed conveyor side (single and dual conveyor)

Two requirements for changing the fixed conveyor sides:

 Conveyor - excess width– moves the fixed conveyor side 34 mm outwards

 Widened conveyor – moves the conveyor sides of the 2nd conveyor to the limit switch

Single conveyor mode (D-Series up to 380 mm/HF, X lines up to 450 mm)

Belt tension for lane 1

(Single and dual conveyor)

for lane 2

(dual conveyor)

Belt tension for the width

adjustment

24 Hz +/-2 Hz

Eingabeband 170 Hz +/-10 Hz 170 Hz +/-14 Hz

Placement area 1 70 Hz +/-7 Hz 77 Hz +/-7 Hz

Intermediate conveyor 147 Hz +/-9 Hz 118 Hz +/-9 Hz

Placement area 2 70 Hz +/-7 Hz 77 Hz +/-7 Hz

Ausgabeband 170 Hz +/-10 Hz 170 Hz +/-14 Hz

Settings for the belt tension

NOTE:

This menu is protected with the

Siemens Service password.

 The fixed conveyor side can be set in SITEST

if required.

 If the position of the fixed conveyor side which

has been taught is saved, these values will be

used for the function

Move all conveyor ed-

ges to standard position

The default values will be overwritten and will

need to be retaught.

 If these dimensions are incorrectly set on the

single or dual conveyor, the PCB reference

corner may be moved, leading to fiducial

errors during placement.

NOTE:

In the SR/MC station SW, the fixed conveyor side of all lanes can be adjusted

in the conveyor firmware (flexible). However, this may only be set with the

SITEST software.

NOTE:

In the D-Series machines, you need to remove the clamping rings on the fixed

conveyor side in advance.

Modular conveyor

Conveyor Settings Setting the fixed conveyor side (single and dual conveyor)

Student Guide SIPLACE D4 (FSE)

Modular conveyor EN 09/2006

262

11.3.2.1 Widening the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode)

X Select

Option and configuration

from the SITEST conveyor menu and then click on

Widen

conveyor

to widen the conveyor.

X The conveyor sides of the 2ndconveyor lane (right side fixed (lane 1 left side fixed)) are moved to

the limits.

X The SITEST SW ask for connecting the lifting tables.

Widening the board conveyor (from its standard width) allows you to use boards up to 380 mm wide.

Widening the board conveyor from the mode "Widened" to the mode "excess width" allows you to place

boards up to a width of 430 mm.

11.3 - 2: Setting the "fixed conveyor side" in SIPLACE D-Series

NOTE:

The fixed conveyor side should be adjusted only with the SITEST software and

the width adjustment devices. This ensures that the conveyor runs straight.