CP-6-series Mechanical Reference.pdf - 第105页
2.1 Lubricating the XY -table <CP-6/6E, CP-6M/6ME> Arrow marks in the illustration indicate lubrication points. Black arrows indicate points where a grease gun is required. Apply to the Y-axis ball screw Apply to t…
Lubrication Instructions
Illustrations and tables are used to indicate important information about keeping the
machine properly lubricated.
■ Type and Schedule for Lubrication
Within these illustrations, symbols are used to indicate the location, type and schedule
for lubrication.
The lubrication schedules are based on eight hours of operation per day, five days per
week (40 hours) and 20 days per month (160 hours). However, if the machines are being
operated in two or three shifts per day, the lubrication schedules should be used as
follows.
Daily: Eight hours from when the machine is turned on, after every
eight hour shift, or after one day’s operation.
Weekly: After 40 hours of operation, whether the machine is being used
in two or three shifts, or after one week’s operation.
Monthly: After 160 hours of operation, whether the machine is being
used in two or three shifts, or after one month’s operation.
Every 3 months: After 480 hours of operation, whether the machine is being
used in two or three shifts, or after three month’s operation.
■ Locations for Lubrication
Locations for lubrication are indicated in the illustrations using arrows and numbers.
White arrows are used to indicate surfaces that require greasing or oil. Black arrows
indicate grease fittings, and signify that grease should be inserted using a grease pump.
Note: Even LM blocks that do not have a grease fitting can be lubricated by applying grease
between the block and the LM rail (bearing mechanism). The grease that adheres to the
ball bearings and rollers will be taken into the LM block and thereby serve to lubricate the
LM block.
■ Lubrication Checklist
A lubrication checklist is provided at the end of this chapter. This checklist should be
used as follows.
1. Check the lubrication points corresponding to the reference numbers shown in the
illustrations.
2. Mark each check box after lubricating each point.
LM rail
LM block
(1)
(2)
C7SM3004
Part 3 Chapter 2 Lubrication
Edition 1.2 3-2-3 CP-6-series Mechanical Reference
2.1 Lubricating the XY-table
<CP-6/6E, CP-6M/6ME>
Arrow marks in the illustration indicate lubrication points.
Black arrows indicate points where a grease gun is required.
Apply to the Y-axis ball screw
Apply to the X-axis ball screw
(1) :
(4) :
Z-axis
CP6M3010
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(9)
(8)
(8)
(8)
(8)
(10)
(10)
(11)
AFC Grease
Daphne
Eponex No. 2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
✔
✔
✔
N/A
✔
✔
✔
✔
✔
✔
✔
N/A
N/A
N/A
✔
CP6M3009
Lubrication
Points
Lubrication
Frequency
Types of Lubricants
1
2
3
4
5
6
7
8
9
10
11
Every month
Every week
Every month
Every month
Every week
Every month
Every week
Every month
Every month
Every month
Every month
✔ : Lubricate N/A : Do not lubricate
Ball screw
Ball screw
Gear, Rack gear
Z-axis cam side
Z-axis LM rail
LM rail
Shaft
LM
guide
LM
guide
LM rail
LM block
LM rail
LM block
Part 3 Chapter 2 Lubrication
Edition 1.2 3-2-4 CP-6-series Mechanical Reference
<CP-642/642E, CP-642M/642ME, CP-643E/643ME>
Arrow marks in the illustration indicate lubrication points.
Black arrows indicate points where a grease gun is required.
Same for Y-axis
Z-axis ball screw:
Apply multemp LRL3 or SRL
CP6M3012a
(12)
(13)
(13)
(14)
(15)
(16)
(16)
(17)
(18)
Multemp
LRL3
Multemp
SRL
Z-axis ball screw
Daphne
Eponex
No. 2
N/A
N/A
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
N/A
N/A
N/A
N/A
N/A
N/A
N/A
✔
CP6M3011a
Lubrication
Points
Lubrication
Frequency
Types of Lubricants
12
13
14
15
16
17
18
Every month
Every week
Every month
Every month
Every week
Every month
Every month
✔ : Lubricate N/A : Do not lubricate
Ball screw
Ball screw
LM
guide
LM rail
LM block
LM
guide
LM rail
LM block
(Except for
CP-643E/643ME)
(Only for
CP-643E/643ME)
Part 3 Chapter 2 Lubrication
Edition 1.2 3-2-5 CP-6-series Mechanical Reference