1OM-1075-002.pdf - 第67页
*6 [LOCK] Lamp • While this lamp is "ON", it indicates that only the rear operation panel is available and no panel change operation is possible. • The lamp flickers when any operation is made on the front oper…
*3 [STOP] Button
• This button is used to stop the automatic operation.
• When this button is pressed during zeroing operation, the zeroing
operation of each device is interrupted, excluding the P.C.B. trans-
fer.
*4 [ENABLE] Button
• When the [ON] button (entitled "MOVE") is pressed in the active
operation sheet, the LED of the [ENABLE] button illuminates for
two seconds.
When the [ENABLE] button is pressed with its LED "ON", the ma-
chine performs various operations selected in the operation sheets.
*5 [PNL CHANGE] Button
• This button is used to select either the front or the rear operation
panel.
(a) The other operation panel can be selected by press-
ing the [PNL CHANGE] button on the unavailable (in-
valid) side only when the currently selected panel is
not set in the "Operation Locked" mode.
(b) While the LED of this button is ON, the followings
become available.
Rear Touch Screen
[START] Button
[STOP] Button
[ENABLE] Button
[READY] Button
[OPERATION] Switch
[EMERGENCY STOP] Switch
(c) The [STOP] button and [EMERGENCY STOP] switch
are always available regardless of the [PNL CHANGE]
button.
(d) When the panel operation is not locked and the
[STOP] button on the unselected operation panel is
pressed, the operation panel on the pressed button
side becomes activated automatically.
• When this button is pressed with the LED "ON", the "LOCK" lamp
illuminates, indicating that only the rear panel is available (Opera-
tion Locked).
To cancel the "LOCK" mode, press this button again.
0308-003 1-21
AHB01EOPP
2.3 Equipment for Operations
Note
*6 [LOCK] Lamp
• While this lamp is "ON", it indicates that only the rear operation
panel is available and no panel change operation is possible.
• The lamp flickers when any operation is made on the front opera-
tion panel with the lamp being kept ON.
To cancel the flickering of the lamp, press the [PNL CHANGE]
button and follow the steps to set the operation-lock mode again.
*7 [READY] Button
• This button is used to turn on or off the electromagnetic lock of the
rear safety door.
ON : The electromagnetic lock of the rear safety door is turned
ON.
OFF : The electromagnetic lock of the rear safety door is turned
OFF.
*8 [OPERATION] Switch
• The selection key must be inserted to change over the [OPERA-
TION] switch to "RUN" or "SETUP".
The [OPERATION] switch must be set to the "RUN" side for auto-
matic operation.
The switch can be changed over to "RUN" or "SETUP"
only when the machine is in the "STOP" mode.
• When the switch is changed to the "SETUP" side, the machine is
set as follows.
(a) The red, yellow, and green lamps of the light tower will illumi-
nate (initial setting of the machine upon shipment).
(b) The following operations are prohibited regardless of the rear
safety door condition (opened/closed).
Automatic Operation, Zeroing Operation, Device Check,
Unit Adjustment, and Teaching Operation
(c) Operations automatically become available on the rear op-
eration panel (operations locked).
No operations are accepted on the front operation panel.
• When the [OPERATION] switch is set to the
"SETUP" side, the interlock system of the rear safety
door is deactivated.
• Do not operate the machine with the [OPERATION]
switch in the "SETUP" mode except for the setup
operations.
• Do not keep the selection key inserted unless nec-
essary. The key shall be stored by the person in
charge.
• When the selection key is turned forcibly, the switch
may be damaged.
0308-003 1-22
AHB01EOPP
2.3 Equipment for Operations
Note
CAUTION
*9 [EMERGENCY STOP] Switch
• This switch is used to stop the machine immediately in an emer-
gency.
• When this switch is pressed, the power is turned off and the ma-
chine stops immediately.
When the power is turned off, the LED of the [POWER ON] but-
ton on the operation panel illuminates in red.
*10 Rear Touch Screen
• The operation windows will be displayed on the rear touch screen
as well as the front one.
Various types of operations become available by touching the but-
tons and tabs on the screen.
*11 Working Lamp Switch
• This switch is used to turn on or off the working lamp on the rear
side.
*12 Cycle Counter
• This counter counts how many times (cycles) the machine has
worked.
0308-003 1-23
AHB01EOPP
2.3 Equipment for Operations