FlexTRAK 2MB Material Handler Addendum Rev 05.pdf - 第123页

FlexTRAK Series 2MB Mater ial Handler Adden dum Operations © 2023 Nordson Corporation 6-19 6.7.6 M ani pulating the Lane 1 Conveyor Use these controls to manually manipulate and view conveyor parameters for Lane 2, see 6…

100%1 / 166
FlexTRAK Series 2MB Material Handler Addendum Operations
6-18 © 2023 Nordson Corporation
?
NOTE Adjusting the lane speed for the load sequence also updates the lane speed of
the unload sequence.
3. Touch the JOG SPEED field to set the speed of both lanes after the LOAD IN TIME has
expired.
„ The conveyor will operate at this speed until the board reaches Detect 4.
4. Touch the NEXT PART DELAY field to set the time delay of both lanes when the MH
begins waiting for the upstream machine to load a part.
„ The timer will count down for the displayed amount of time. If a Board Available signal
is not sent from the upstream machine within the set time, the next machine sequence
will be initiated.
5. Touch the LOAD IN TIMER to set the timer initiated after a board is completely detected
on the conveyor.
„ The timer affects both lanes. The conveyor will operate at the lane speed for the
displayed amount of time, at which point the conveyor speed will reduce to the jog
speed.
Unload Sequence
1. Touch the LANE SPEED field to set the initial speed of both lanes when a conveyor
unload sequence is initiated.
„ The unload sequence also starts the HS unload timer.
?
NOTE Adjusting the lane speed for the unload sequence also updates the lane speed of
the load sequence.
2. Touch the UNLOAD SPEED field to set the speed of both lanes after the HS UNLOAD
TIMER has expired.
„ Typically, this speed is set to match the downstream machine’s conveyor speed.
3. Touch the HS UNLOAD TIMER field to set the timer initiated when a lane begins to
unload a board.
„ Until the timer expires or Detect 5 is activated, the conveyor will operate at the Lane
SPEED setting for the displayed amount of time, at which point the conveyor speed
will reduce to the UNLOAD SPEED setting for both lanes.
4. Touch the BOAT OUT DELAY field to set the time delay of both lanes.
„ The timer is started once Detect 5 is initially activated. It must be inactivated for the
displayed amount of time before the conveyor lane is considered cleared of a board. If
at any time Detect 5 becomes active, the timer will reset and start again.
FlexTRAK Series 2MB Material Handler Addendum Operations
© 2023 Nordson Corporation 6-19
6.7.6 Manipulating the Lane 1 Conveyor
Use these controls to manually manipulate and view conveyor parameters for Lane 2, see 6.7.4
Manipulating the Lane 2 Conveyor.
To manipulate the lane 1 conveyor:
1. Touch the MATERIAL HANDLER button on the FlexTRAK PM Overview screen.
„ The MH Overview screen opens (Figure 5-4).
2. Touch the MAINTENANCE button.
„ The Maintenance Master screen opens (Figure 5-5).
3. Touch the SHUTTLER button.
„ The Axis Status screen opens (Figure 5-6).
4. If manual mode is not enabled, touch the MANUAL button.
5. Touch the CONVEYOR button.
„ The Conveyor Status screen opens (Figure 6-16).
6. Touch the MR1 MANUAL button to toggle the Machine Ready Signal ON or OFF.
7. Touch the BA1 MANUAL button to toggle the Board Available Signal ON or OFF.
?
NOTE BA/MR appear and disappear based on the separator position. If the separator is in
Lane 1, BA1/MR1 appears in Lane 1. If the separator is in Lane 2, BA2/MR2 appears in
Lane 2. If the separator is out of position (not in Lane 1 or in Lane 2), no BA/MR
appears.
8. Touch the LOAD Lane 1 button to manually turn on Lane 1.
„ Once enabled, a board is expected to arrive at the chamber pick position within 20 sec.
An internal timer begins to count down and will cause a load in alarm if exceeded. The
MANUAL ALARMS switch on the Parameters screen (Figure 5-15) can manually
override this alarm.
9. Touch the UNLOAD Lane 1 button to manually turn on Lane 1.
„ Once enabled, a board is expected to depart the conveyor within 20 sec. An internal
timer begins to count down and will cause an unload alarm if exceeded. The MANUAL
ALARMS switch on the Parameters screen (Figure 5-15) can manually override this
alarm.
10. Touch the STOP 1 MANUAL button to toggle Lane 1’s board stop UP or DOWN.
FlexTRAK Series 2MB Material Handler Addendum Operations
6-20 © 2023 Nordson Corporation
6.7.7 Manually Test Motor Control
Use these controls to manually test the motor functionality of Lane 1 and Lane 2.
To manually test motor control:
1. Touch the MATERIAL HANDLER button on the FlexTRAK PM Overview screen
(Figure 6-6).
„ The MH Overview screen will open (Figure 5-4).
2. Touch the MAINTENANCE button.
„ The Maintenance Master screen opens (Figure 5-5).
3. Touch the SHUTTLER button.
„ The Axis Status screen opens (Figure 5-6).
4. If manual mode is not enabled, touch the MANUAL button.
5. Touch the CONVEYOR button.
„ The Conveyor Status screen opens (Figure 6-16).
6. Touch the MANUAL SPEED button to set the speed of both lanes.
7. Touch the MTR 2 MANUAL button to toggle the belt drive motors of Lane 2 ON or MAN.
„ When the motor control of Lane 2 is in Manual mode, all other Lane 2 speeds are
disabled and the conveyor will only run at the speed set in the MANUAL SPEED field.
8. Touch the MTR 1 MANUAL button to toggle the belt drive motors of Lane 1 ON or MAN.
„ When the motor control of Lane 1 is in Manual mode, all other Lane 1 speeds are
disabled and the conveyor will only run at the speed set in the MANUAL SPEED field.
6.7.8 Manipulating Separator Parameters
Use these controls to manually manipulate and view separator parameters. The separator controls the
movement of Lane 2.
To manipulate separator parameters:
1. Touch the MATERIAL HANDLER button on the FlexTRAK PM Overview screen.
„ The MH Overview screen will open (Figure 5-4).
2. Touch the MAINTENANCE button.
„ The Maintenance Master screen opens (Figure 5-5).
3. Touch the SHUTTLER button.
„ The Axis Status screen opens (Figure 5-6).
4. If manual mode is not enabled, touch the MANUAL button.
5. Touch the CONVEYOR button.
„ The Conveyor Status screen opens (Figure 6-16).