N7201A652E.pdf - 第384页
NPM- TT2 EJM1E E-MB-05O-05 5-1-1 -7 Setting information 6 Unit setting Option setting 4 Operating procedure 5-1-1 ● Default ： OFF ■ Feeder No. Item name Function when [ON] is selected 1 Feeder maint warning Displays a w …
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-6
Setting information 5
System
administration
No. Item name Function when [ON] is selected
1 Force PCB Eject
Ejects PCB forcibly even if there is no PCB request signal from the
downstream machine.
2
Pre process other
company M/C joint
Makes the timing of PCB request signal OFF from the downstream machine
earlier.
3
Pre process other
company M/C joint2
Hastens the timing of PCB request signal OFF from the downstream machine.
4
All pattern bad board
pass
When all patterns are judged to be bad by bad mark recognition, this option
unloads the board to the downstream side without mounting parts on it.
5 F Proc. Eject Wait
When a third-party machine or conveyor is connected on the upstream side,
and “B. A. (Board Available) signal from it is received, PCB request signal is
sent to the upstream machine or conveyor, and a PCB is loaded.
6
Production item name
check
When this option is ON, the NPM machine checks the product name before a
PCB is loaded from the upstream machine. If the production data names do
not agree, the NPM comes to a single error stop.
7
Width adjustment
fixed
Disables width adjustment at any operation screen even during automatic
operation.
8
PCB connection
detect
Determines an error if two PCBs connected with onto each other are loaded.
9
Conveyor width check
before production
Checks that the conveyor width matches the setting in the production data
before starting production.
10
Positioning action
when overrun
Allows positioning to be performed again if a loaded PCB has overrun.
11
PCB Y clamp
(option)
Keeps the Y clamp engaged also during mounting.
12
Multiple lot prevent
carrying (option)
Controls the board transfer during dual lane production so that the
subsequent lot will not overtake the lot ahead.
● Default ：OFF
■ Conveyor
No. Item name Function when [ON] is selected
11
Mount blow check
When checks are made for any component that has not been mounted but
carried back by the nozzle, the mount blow is also checked for any problem.
12
Bad nozzle set during
nozzle stuff
In the event of detection of a stuffed nozzle during production preparation,
the nozzle is automatically set as bad nozzle and production operation is
continued.
● Default ：OFF
■ Head
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-7
Setting information 6
Unit
setting
Option setting 4
Operating procedure
5-1-1
● Default ：OFF
■ Feeder
No. Item name Function when [ON] is selected
1 Feeder maint warning
Displays a warning message when the shot count of tape feeder has
exceeded the warning value.
2
Part remainder number
warning
Displays a warning message when “Feeder remainder number warning
length” in “Action parameters” is reached.
3
Simple Remain
Manage
When the remainder of a reel used reaches 1, this option resets the
remainder, assuming that the reel has been used up.
4
Supply parts count
input when running
Allows the supply parts count for splicing to be input without stopping
production.
5 Splicing length stop
Causes the machine a single stop when the remaining reel is less than 1
200 mm (minimum length required for splicing).
6
Fdr parts collation
(option)
If tape feeders containing any parts different from those in the production
data downloaded to the machine are loaded, the interlock function of the
machine is activated, causing the machine to stop due to an error.
7
Unconditional parts
splicing
Enable parts to be re-verified when feeder parts verification is ON, even
though splicing verification has already been done.
8
Component splicing
executes when
remaining warning
happen
Enables splicing only for tape feeders with which a remainder warning has
occurred.
9 Feeder deploy free
Allows a tape feeder containing the same parts can be placed at any
desired slot before starting production or if parts empty has occurred. When
the specified feeder is used up, the arranged feeder is used automatically to
continue production.
10
Pick up sequence has
high priority when free
arrange
Gives priority to simultaneous pickup if it is involved when picking up parts
with “Feeder deploy free” ON. Notifies the operator that the cycle time may
be slower depending on the tape feeder arrangement.
11
Fdr parts collation
(Time of feeder set )
If tape feeders have been removed/set during single stop, this option
executes parts collation for the feeders concerned after production is
started. If there is no problem, production continues. If any problem is found,
a message “Hasn’t executed parts verification” appears and the machine
stops.
12
Feeder outside parts
collation
Enables tape feeder collation by the customer’s parts collation system.
When replenishing parts after a parts empty error, this option inquires of the
parts collation system whether collation has done. If collated, parts
replenishment will be completed to continue production. If not collated,
parts replenishment is considered to be unfinished and production will be
stopped.
13
Substituted parts auto
change
Enables pickup of substitute parts using the registered data when the
master parts are used up.
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-8
Setting information 7
System
administration
● Default ：OFF
■ Feeder
No. Item name Function when [ON] is selected
14
All arranged
components supply
target
Allows loading of tape feeders that contain any parts registered in the
arrangement list.
15
Auto Cart Height
Measure
When several feeder carts are used for one machine, pickup rate lowers due
to variation in the height of cart. To prevent this problem, this option
measures the height of reference post automatically to make correction.
16 Stop at S-tape sense
Causes the machine a single stop if the splicing tape is detected, and
displays an error message “Splicing tape detection stop”.
17
Trans material empty
check of syringe
(front)
(Currently unused)
Detects material empty of the syringe (supply tables A to D) by the sensor
mounted on the transfer unit.
18
Trans material empty
check of syringe(rear)
(Currently unused)
Detects material empty of the syringe (supply tables A to D) by the sensor
mounted on the transfer unit.
19
Feeder mark
recognition
Recognizes the mark at the retainer of the feeder tape, to perform pickup
position teaching automatically.
Pickup position teaching is not required for transparent embossed tape and
12 mm or wider feeder parts.
20
Disused Feeder LED
Blink at AutoProd
Start
At the start of running blink the green LED of unused feeder in the production.
So that it can be noticed by one glance.
21
Certify Feeder First
Pick Up Pos Teach
after Change over
Displays the screen that shows the feeder pickup position after production
changeover. Confirm the pickup position before the first pickup.
22
Confirm stock parts
verification again
Displays a window for confirming the target parts when parts with stock have
been collated.
23
8mm feeder(paper)
gap correct function
If a recognition error has occurred with a part that requires pocket recognition
at the start of recognition, the tape is fed by a half pitch automatically. If the
part is present, correction is made after the pocket is recognized again.
24
Pick up position teach
Parts shape display
Displays a frame showing the shape of part on the Pickup position teach
screen (Arrange - PartsPrepare - Feeder - Pickup pos) and Pickup position
check error screen.
25
Prevention of feeder
over-exposure
Changes the input range for the second origin offset according to the size of
the flat chip (to prevent values beyond the half of the part size from being set
as the second origin offset).
26
Prevention of 1mm
pitch next parts over-
exposure
Applicable only to components of feed pitch 1 mm. This function prevents the
next component from being exposed. Each time at the pickup position T, the
target learned value is reset to return the tape feed to origin. Then, the pickup
position is corrected with respect to the feeder cover mark.