N7201A652E.pdf - 第393页

NPM- TT2 EJM1E E-MB-05O-05 5-1-1 -16 System administration Setting information 15 No. Item name Function w hen [ON] is selec ted 1 Production report clear at auto product change Clear s the p roduction re port at produc …

100%1 / 512
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-15
Setting information 14
Unit
setting
Option setting 8
Operating procedure
5-1-1
No. Item name Function when [ON] is selected
1
Measure by the
height sensor (front)
Measures the board height (warp) by the height sensor, in order to control the
nozzle height during mounting.
2
Measure by the
height sensor (rear)
Measures the board height (warp) by the height sensor, in order to control the
nozzle height during mounting.
● Default ：OFF
■ Height sensor
No. Item name Function when [ON] is selected
1
Over judge input
again
When inspection by the inspection head has resulted in NG, this option
allows judgment (OK/NG) for the NG component to be input again on the
Over judge screen.
● Default ：OFF
■ Inspection head
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-16
System
administration
Setting information 15
No. Item name Function when [ON] is selected
1
Production report
clear at auto product
change
Clears the production report at production changeover.
2
Production report
clear at the other lot
name auto product
change
Clears the production report only when changing production to a different lot
name.
The report is cleared also when the MJS ID differs.
3
Display transfer
direction of status
monitor PCB
Displays the PCB flow direction on the Status monitor screen.
4
Buzzer stop button
auto change
Changes the function button to [Buzzer stop] automatically when the buzzer
sounds.
5 PCB warp correction
Estimates the board warp based on the heights measured by sensor at
several points on the board, in order to control the mounting height.
6
Pre-pickup inspection
at run resume
Executes pre-pickup check if suspended automatic operation is restarted on
the Production start screen
No. Item name Function when [ON] is selected
1
Time-lapse change
calibration
Performs calibration for time-lapse change.
No. Item name Function when [ON] is selected
1
Vacuum sensor error
detection
Detects error by the vacuum sensor during automatic operation.
2
Nozzle holder filter
detect during head
maintenance
Detects the presence of nozzle holders when the head maintenance unit is
used.
● Default ：ON
■Whole (suspension)
● Default ：ON
■ XY unit (suspension)
● Default ：ON
■ Head (suspension)
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-17
Setting information 16
Unit
setting
Option setting 9
Operating procedure
5-1-1
No. Item name Function when [ON] is selected
1 PCB in when stop
Prohibits the loading of next PCB from the upstream process during single
stop or cycle stop.
2 PCB out when stop
Carries out the PCB waiting in the machine to the downstream process
during single stop or cycle stop.
3 Wait between MC
Determines whether or not to have a PCB held in between the machines in
the line where the NPM is directly connected upstream or downstream the
machine.
4 Simultaneous transfer Enables PCB unloading and loading of the next PCB at the same time.
5
Support action time
being shortened
Lowers the support to the “both sides mount height”, and raises it after the
next PCB is loaded.
6
Keep clamping in
cycle stop
Keeps the clamp engaged during cycle stop.
7 Pre carry out
Unloads PCBs, to which post waiting is not available, into a place as far away
as possible upon completion of placement.
No. Item name Function when [ON] is selected
1
Cover tape error
detected
Detects cover tape (cover tape) exhaust and tape jamming error.
2
Tape joint error
detect
Detects tape joint error.
3
Component remains
input
Allows the part remainder to be input manually after splicing.
4
Syringe trans material
empty stop
Causes the machine a single stop if material empty has been detected by
the sensor during automatic operation.
5
Tape feed during the
production
Feeds the tape during production.
6
Return to origin after
pickup pos teach
Performs origin return after pickup position teaching. When OFF is selected,
one part will be fed after pickup position teaching.
● Default ：ON
■ Conveyor (suspension)
● Default ：ON
■ Feeder (suspension)