N7201A652E.pdf - 第385页

NPM- TT2 EJM1E E-MB-05O-05 5-1-1 -8 Setting information 7 System administration ● Default ： OFF ■ Feeder No. Item name Function w hen [ON] is selec ted 14 All arranged components supply target Allows loading of tape feed…

100%1 / 512
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-7
Setting information 6
Unit
setting
Option setting 4
Operating procedure
5-1-1
● Default ：OFF
■ Feeder
No. Item name Function when [ON] is selected
1 Feeder maint warning
Displays a warning message when the shot count of tape feeder has
exceeded the warning value.
2
Part remainder number
warning
Displays a warning message when “Feeder remainder number warning
length” in “Action parameters” is reached.
3
Simple Remain
Manage
When the remainder of a reel used reaches 1, this option resets the
remainder, assuming that the reel has been used up.
4
Supply parts count
input when running
Allows the supply parts count for splicing to be input without stopping
production.
5 Splicing length stop
Causes the machine a single stop when the remaining reel is less than 1
200 mm (minimum length required for splicing).
6
Fdr parts collation
(option)
If tape feeders containing any parts different from those in the production
data downloaded to the machine are loaded, the interlock function of the
machine is activated, causing the machine to stop due to an error.
7
Unconditional parts
splicing
Enable parts to be re-verified when feeder parts verification is ON, even
though splicing verification has already been done.
8
Component splicing
executes when
remaining warning
happen
Enables splicing only for tape feeders with which a remainder warning has
occurred.
9 Feeder deploy free
Allows a tape feeder containing the same parts can be placed at any
desired slot before starting production or if parts empty has occurred. When
the specified feeder is used up, the arranged feeder is used automatically to
continue production.
10
Pick up sequence has
high priority when free
arrange
Gives priority to simultaneous pickup if it is involved when picking up parts
with “Feeder deploy free” ON. Notifies the operator that the cycle time may
be slower depending on the tape feeder arrangement.
11
Fdr parts collation
(Time of feeder set )
If tape feeders have been removed/set during single stop, this option
executes parts collation for the feeders concerned after production is
started. If there is no problem, production continues. If any problem is found,
a message “Hasn’t executed parts verification” appears and the machine
stops.
12
Feeder outside parts
collation
Enables tape feeder collation by the customer’s parts collation system.
When replenishing parts after a parts empty error, this option inquires of the
parts collation system whether collation has done. If collated, parts
replenishment will be completed to continue production. If not collated,
parts replenishment is considered to be unfinished and production will be
stopped.
13
Substituted parts auto
change
Enables pickup of substitute parts using the registered data when the
master parts are used up.
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-8
Setting information 7
System
administration
● Default ：OFF
■ Feeder
No. Item name Function when [ON] is selected
14
All arranged
components supply
target
Allows loading of tape feeders that contain any parts registered in the
arrangement list.
15
Auto Cart Height
Measure
When several feeder carts are used for one machine, pickup rate lowers due
to variation in the height of cart. To prevent this problem, this option
measures the height of reference post automatically to make correction.
16 Stop at S-tape sense
Causes the machine a single stop if the splicing tape is detected, and
displays an error message “Splicing tape detection stop”.
17
Trans material empty
check of syringe
(front)
(Currently unused)
Detects material empty of the syringe (supply tables A to D) by the sensor
mounted on the transfer unit.
18
Trans material empty
check of syringe(rear)
(Currently unused)
Detects material empty of the syringe (supply tables A to D) by the sensor
mounted on the transfer unit.
19
Feeder mark
recognition
Recognizes the mark at the retainer of the feeder tape, to perform pickup
position teaching automatically.
Pickup position teaching is not required for transparent embossed tape and
12 mm or wider feeder parts.
20
Disused Feeder LED
Blink at AutoProd
Start
At the start of running blink the green LED of unused feeder in the production.
So that it can be noticed by one glance.
21
Certify Feeder First
Pick Up Pos Teach
after Change over
Displays the screen that shows the feeder pickup position after production
changeover. Confirm the pickup position before the first pickup.
22
Confirm stock parts
verification again
Displays a window for confirming the target parts when parts with stock have
been collated.
23
8mm feeder(paper)
gap correct function
If a recognition error has occurred with a part that requires pocket recognition
at the start of recognition, the tape is fed by a half pitch automatically. If the
part is present, correction is made after the pocket is recognized again.
24
Pick up position teach
Parts shape display
Displays a frame showing the shape of part on the Pickup position teach
screen (Arrange - PartsPrepare - Feeder - Pickup pos) and Pickup position
check error screen.
25
Prevention of feeder
over-exposure
Changes the input range for the second origin offset according to the size of
the flat chip (to prevent values beyond the half of the part size from being set
as the second origin offset).
26
Prevention of 1mm
pitch next parts over-
exposure
Applicable only to components of feed pitch 1 mm. This function prevents the
next component from being exposed. Each time at the pickup position T, the
target learned value is reset to return the tape feed to origin. Then, the pickup
position is corrected with respect to the feeder cover mark.
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-9
Setting information 8
Unit
setting
Option setting 5
Operating procedure
5-1-1
● Default ：OFF
■ Feeder
No. Item name Function when [ON] is selected
27
Trans unit
screen(Step
Exchange) operation
limited
Disables operation buttons other than the transfer supply time setting buttons
when the Operator mode is selected.
28
Feeder defective rate
warning (specified
count)
If the feeder error rate among the 100 most recent pickups is more than the
specified defective feeder rate, a warning is displayed. If the setting is OFF,
error rate from the start of automatic operation is calculated, and a warning is
displayed if the specified defective feeder rate is exceeded.
29
Thin Type Single
Feeder
Allows the thin type single feeders to be used.
30
Pickup position teach
before the production
start
Causes all machines to perform pickup position teaching before starting
production.
31
Display pickup
position teach when
occurred feeder error
Moves the head to the pickup position of the tape feeder if the machine comes
to a single stop due to any of the following feeder errors.
32
Product Continue
when No Splicing
Check
If a “no splicing check” error has occurred, this option allows the machine to
continue operation with the feeders containing the mountable components,
and then stops operation.
33
Force whole feed after
splicing tape detected
For the reels specified as “whole feed” in the production data, even if joint
detection is canceled when stopped due to “No splicing check”, whole feed is
carried out without fail when the detection position comes to the pickup
position.
34
Tape guide check
again
Conduct a tape guide check again after the insertion or removal of AL (auto
load) feeder, regardless of whether you have conducted a tape guide check
before the removal of the AL feeder.
35
Feeder pulling and
inserting monitoring in
arrangement
When “Feeder parts collation (parts loaded) 2” is enabled, feeders are
checked even during setup. If any feeder has been inserted or removed,
operation cannot be started until components are verified.
36
Save pickup position
when feeder error
occurred
The image on the pickup position recognition error screen that has been
shown by the “Pickup position display at feeder errors” function is captured
and saved in the LNB.
37
Pickup again in start
up tape status
When the “Pickup error recovery” function is used, recovery for pickup error is
carried out even during tape feed start.
38
Adjacent lane pickup
position teach when
inserting feeder
The feeders on the left and right of the inserted feeder are also subject to
pickup position teaching.
39
Large parts pickup
position Auto teach
extend
When pickup position auto teaching for 12 mm or wider feeders is performed,
the feed hole is recognized followed by the pocket. Teaching is finished if
either of them is recognized successfully.