N7201A652E.pdf - 第503页
NPM- TT2 EJM1E E-MB-06O-04 6-1-7 -2 At a glance
NPM-TT2 EJM1EE-MB-06O-04
6-1-7-1
Nozzles are compatible between the nozzles for the NPM 3-nozzle head and those for CM301/ CM202/
CM120/ CM100 by replacing orifices, or attaching or detaching new ones.
■Divided-type nozzles
(1001, 1002 nozzle)
■Integral-type nozzle
(1003,1004,1005, special nozzle)
■Divided-type nozzles
(1001, 1002 nozzles)
■Integral-type nozzle
(1003,1004,1005, special nozzle)
Orifices C
(KXFB03KPA00)
Dedicated orifices B
(KXFB03KNA00)
Specifi-
cation
Compatibility among
nozzles
Orifices A
(KXFB01MPA00)
Orifices A Orifices B
Orifices C
CM301
CM202
CM120
CM100
Operating procedure
6-1-7
CM101 CM212
CM232 CM400
CM401 CM402
CM602 DT401
NPM series
NPM-TT2 EJM1EE-MB-06O-04
6-1-7-2
At
a glance
NPM-TT2 EJM1EE-MB-06O-04
Specifi-
cation
Operating procedure
6-1-8
6-1-8-1
Height sensor
Appearance
Applic
-able
PCB
*1)
PCB dimensions
PC size
300mm
transfer specifications
Dual lane mode
●Min: L 50 × W 50mm ●Max: L 510 × W 300mm
Single lane mode
●Min: L 50 × W 50mm ●Max: L 510 × W 590mm
PCB dimensions
M size 260mm
transfer specifications
Dual lane mode
●Min: L 50 × W 50mm ●Max: L 510 × W 260mm
Single lane mode
●Min: L 50 × W 50mm ●Max: L 510 × W 510mm
Thickness 1.6 to 8.0 mm
Material Glass epoxy
Measured surface
material
Copper foil + resist face, There should be area of at least 1.5
1.5mm on the copper foil and silk face.
The transparent and semi-transparent area are not target. (Glass
epoxy material face)
PCB warpage
amount
Upper warp: 2 mm or less, lower warp: 2 mm or less, and warp
gradient:0.5 % or less, The difference in height of an edge line
(transfer direction): 1 mm or less.
Function
Warpage toralrance
detection
If the measurement result exceeds tolerance, give a warning before
placement start. Also confirm the tolerance warp gradient (%).
Height control
Measures the PCB whole height (warpage) and control the
placement height.
Measured data
transfer
The data measured in the head machine in NPM-W is transferred
to the downstream machine.
The machine in downstream must be NPM-TT2. The data cannot
be sent to the machine other than NPM-TT2.
Regarding a PCB that the warpage shape varies each time it is
clamped, please consult us.
It controls the nozzle height when mounted by measuring the height (warpage) of the entire PCB.
If the measured result exceeds tolerance, give a warning before mount start to prevent the occurrence of PCB
quality defect.
A
B
B
A
Height sensor
NPM-D3 NPM-TT2
Edge line
Transfer direction
Transfer direction
1mmorless
Edge line
Height sensor
*2)