N7201A652E.pdf - 第472页

NPM- TT2 EJM1E E-MB-06O-04 Specifi- cation Mac hine specifica tions/ Basic perf or mance 1 Machine specifications Item Specification Control system Microcomputer system External memory The data is ma naged by LN B *3 ） A…

100%1 / 512
6 At a Glance
NPM-TT2 EJM1EE-MB-06O-04
Specifi-
cation
Machine specifications/
Basic performance 1
Machine specifications
Item
Specification
Control system Microcomputer system
External memory
The data is managed by LNB
*3）
Approximately 1MB is required for a piece of data
Program data
*1）
Placement points Maximum 10 000 points per machine
(Including placement coordinates, recognition mark
coordinates, bad mark coordinates and PCB warpage
measurement points)
* When PCBs are produced in dual lane mode, placement
points shall be the total of front and rear lanes. When
placement points exceed 10 000 points, please consult us.
When your machine line is mixed line with the CM/DT series,
please consult us.
Power
source
Machine body
Normal service power source: Three-phase AC 200 / 220
±10 V, Three-phase AC 380 / 400 / 420 / 480 ±20 V
Frequency: 50 /60 Hz
Peak current value during operation: 40 A (rated voltage AC
200 V)
Rated
capacity
Machine body 2.5 kVA
Supply air pressure 0.5 to 0.8 MPa (working air pressure: 0.500 to 0.505 MPa)
Supply air volume 200 L / min (A.N.R.)
Outside
dimensions
Main body only
W 1 300 D 2 628 H 1 444 mm
(The signal tower and the touchscreen are not included)
With a supply unit
■When a tray feeder
*4）
is connected
W 1 300 D 2 798 H 1 444 mm
(The signal tower and the touchscreen are not included)
■When feeder carts
*4)
are coupled to both the front and rear
sides
W 1 300 D 2 893 H 1 444 mm
(The signal tower and the touchscreen are not included)
Mass
*2）
Main body
2 690 kg per unit (Mass of 200kg per unit of a standard
configuration single tray feeder
*4）
is not included)
Single tray feeder
*4）
200 kg per unit
Feeder cart
*4）
110 kg per unit
Standard configuration
3 090 kg (one main unit and two single tray feeders
*4）
)
Environmental condition
Temperature: 10 to 35C
Humidity: 25 to 75% RH (no condensation)
Transportation and storage condition
Temperature: -20 to 60C
Humidity: 75% RH or less (no condensation)
Altitude 1 000 m or less above sea level
Noise < 70 dB (A)
6-1-1-1
Operating procedure
6-1-1
1)
This machine can modify only some data. The data is created by NPM-DGS.
NPM-DGS is software creating production data for NPM (not included in this product)
2)
Mass of the main body excluding the optional units.
3)
LNB (Line network box) manages the production data shared in the line.
4)
Options
NPM-TT2 EJM1EE-MB-06O-04
Basic performance
6-1-1-2
Item
Specification
8-nozzle head 3-nozzle head
Placement angle 0 to 359 °(It can be set in increments of 0.01°)
Placement range
(→P.6-1-4 ‘Applicable PCB specifications’)
PCB flow direction (→P.6-1-2 ‘PCB flow direction’)
Placement tact time
*1）
(Under optimize conditions)
PC size conveyor
■For 0402, 0603, 1005
36 000 CPH (0.100 s/chip)
■For 0402, 0603, 1005
14 400 CPH (0.250 s/chip)
■For QFP
11 800 CPH (0.305 s/QFP)
M size conveyor
■For 0402, 0603, 1005
34 920 CPH (0.103 s/chip)
■For 0402, 0603, 1005
13 968 CPH (0.258 s/chip)
■For QFP
11 446 CPH (0.315 s/QFP)
Placement accuracy
*1）*2）
(under optimum conditions)
■Placement of 0402, 0603, 1005,
±0.04 mm: Cpk ≧1
■For QFP,
±0.05 mm: Cpk ≧1
(12 12 mm or less)
±0.03 mm: Cpk ≧1
(12 12 to 32 32 mm or less)
■For QFP,
±0.03 mm: Cpk ≧1
Target component
Component dimensions
( 0402 chip)
to 32 32 mm
Component thickness: Max. 12 mm
Component dimensions
( 0603 chip)
to 150 25 mm
(opposite side152.1 mm or less)
Component thickness: Max. 30 mm
Mass: Max. 30 g
PCB change time
4.0 s (Not placed on its reverse side)
4.4 s (Placed on its reverse side)
*1)
The values may vary with the type of component.
*2)
This is the case where the placement angle is 0°, 90°, 180°, or 270°. They may be affected by rapid changes
in ambient temperature.
At
a glance