Dek-265GSX-User-Manual.pdf.pdf - 第119页

Parameter Definition Alternate Disp Rate This parameter enables the user to select the ratio of alternate dispenses to standard dispenses. No alternate dispense Every dispense Every second dispense etc. Paste With Board …

Parameter Definition

Paste Start This parameter determines start position of the paste dispense measured from

the centre line of the machine. The limits depend on the type of screen fitted.

Minimum

No adapter -255mm

255 -230mm

Sanyo -210mm

Heraeus -172mm

249 -215mm

Default -half the board length

Maximum

No adapter +255mm

255 +230mm

Sanyo +210mm

Heraeus +172mm

249 +215mm

Default +half the board length

Paste stop This parameter determines the stop position of the paste dispense measured

from the centre line of the machine. The maximum value depends on the

type of screen fitted.

Minimum

No adapter -255mm

255 -230mm

Sanyo -210mm

Heraeus -172mm

249 -215mm

Default -half the board length

Maximum

No adapter +255mm

255 +230mm

Sanyo +210mm

Heraeus +172mm

249 +215mm

Default +half the board length

Knead Boards This parameter sets the number of boards to be printed using the knead

sequence.

Minimum 1

Maximum 10

Increment 1

Knead Deposits This parameter sets the number of print strokes to be carried out on each of

the kneaded boards.

Minimum 2

Maximum 20

Increment 1

Paste Knead Period This parameter sets the time period between print cycles which, if exceeded,

initiates a paste knead sequence.

Minimum 0 (paste kneading switched off)

Maximum 30 minutes

Increment 1 minute

Knead After Dispense If this option is enabled and a paste dispense has been performed (either

Manual or Automatic) a paste knead is performed (as defined by the paste

knead parameters in the board file) on the next board immediately following

the paste dispense.

ENABLED; DISABLED

Paste While Clean This parameter enables the machine to carry out a paste dispense while

cleaning the screen. Available modes are:

DISABLED, MODE 1, MODE 2, BOTH MODES

Alternate Disp This parameter gives the option to dispense at either ENDS or CENTRE.

ENDS dispenses at the outer 25% of the squeegees. CENTRE dispenses

along an area of 25% either side of the centre line.

ENDS; CENTRE

1.102 User Manual Software Version 6

MACHINE PROGRAMMING

MENU PARAMETERS

Parameter Definition

Alternate Disp Rate This parameter enables the user to select the ratio of alternate dispenses to

standard dispenses.

No alternate dispense

Every dispense

Every second dispense etc.

Paste With Board This parameter gives the option to dispense paste with a board loaded and

held at print height. This prevents paste dropping through the image on the

screen. Options are:

ENABLED; DISABLED

NOTE

With enabled selected the parameter Paste While Clean is removed.

Board Count This function provides the facility for the print cycle to be halted

automatically on a board count basis. If the board stop count is zero this

function is not active. When a print run is started, a count is made from the

STOP CYCLE AFTER value to zero decrementing by one for each board

printed. When the counter reaches zero, the print cycle is finished and

control returned to the main display page and the beacon is set to amber, thus

indicating that the machine requires operator attention. The operator has

access to all of the machines options. Once the operator has performed any

required operations, the run button can be pressed to continue the print cycle.

Minimum 0 Boards

Maximum 500 Boards

Increments 1 Board

Stop After Idle This parameter when enabled sets the time the product is held in contact with

the screen until both upline and downline systems are ready to transfer.

Minimum 0 mins.

Maximum 200 mins.

Increments 1 min.

Screen X Forward Nominal position of the X front screen actuator which ensures that

corresponding screen and board fiducials can be viewed from a single camera

position.

Minimum -20mm

Maximum +20mm

Increment 0.004mm

Screen X Rear Nominal position of the X rear screen actuator which ensures that

corresponding screen and board fiducials can be viewed from a single camera

position.

Minimum -20mm

Maximum +20mm

Increment 0.004mm

Screen Y Axis Nominal position of the Y screen actuator which ensures that corresponding

screen and board fiducials can be viewed from a single camera position.

Minimum -10mm

Maximum +10mm

Increment 0.004mm

Cleaner Paper

Advance

The distance, measured in millimetres, by which the cleaner paper is

advanced.

Minimum 0

Maximum 200mm

Increment 4mm

SPC Configuration This preference allows the user to set up the Machines SPC operation. On

selecting the SPC Configuration by pressing the Incr. or Decr. buttons, a

window opens and the menu bar changes.

See the SPC Configuration section later in this chapter for further details.

Paste Ridge

Removal

This parameter enables the cleaning option Paste Ridge Removal. This

option removes the ridge of the paste that can develop on the underside of the

screen at the end of the under screen cleaner cleaning stroke.

Disabled; Enabled.

Default Disabled.

Software Version 6 User Manual 1.103

MACHINE PROGRAMMING

MENU PARAMETERS

Parameter Definition

Image Detail This parameter allows the user to modify the screen image data of the

selected screen library file. Once selected, pressing Incr. or Decr. Keys opens

the Image Detail Configuration page.

NOTE

This parameter is only displayed, if Screen Size in Set Preferences has been

selected to Screen Library.

Mesh Front This parameter sets the distance between the inner edge of the screen frame

and the screen glue line at the front of the frame. It defines the area that

should not be contacted by the squeegees/ProFlow.

Minimum 0mm

Maximum Screen Length - 250mm

Increment 0.1mm

Default 38mm

Mesh Rear This parameter sets the distance between the inner edge of the screen frame

and the screen glue line at the rear of the frame. It defines the area that

should not be contacted by the squeegees/ProFlow.

Minimum 0mm

Maximum Screen Length - 250mm

Increment 0.1mm

Default 38mm

Mesh Left This parameter sets the distance between the inner edge of the screen frame

and the screen glue line at the left of the frame. It defines the area that should

not be contacted by the squeegees/ProFlow.

Mimimum 0mm

Maximum Screen Width - 250mm

Increment 0.1mm

Default 38mm

Mesh Right This parameter sets the distance between the inner edge of the screen frame

and the screen glue line at the right of the frame. It defines the area that

should not be contacted by the squeegees/ProFlow.

Minimum 0mm

Maximum Screen Width - 250mm

Increment 0.1mm

Default 38mm

Image X This parameter defines the dimension in the X axis from the right inner edge

of the screen frame to either:

Right hand edge of the image - right justified image

Left hand edge of the image - left justified image

Centre line of the image - centre justified image

Minimum 60mm

Maximum Screen Width - 100mm

Increment 0.1mm

Default 330.4mm

Image Y This parameter defines the dimension in the Y axis from the front inner edge

of the screen frame to either:

Front edge of the image - front justified image

Rear edge of the image - rear justified image

Centre line of the image - centre justified image.

Minimum 60mm

Maximum Screen Width - 100mm

Increment 0.1mm

Default 330.4mm

Image X Justification This parameter defines the position of the image about the Image X

parameter. The image can be left, right or centre justified about Image X.

Options are:

Left; Right; Centre.

Default Centre

1.104 User Manual Software Version 6

MACHINE PROGRAMMING

MENU PARAMETERS