Dek-265GSX-User-Manual.pdf.pdf - 第122页

Parameter Definition Rear Paste Recovery This parameter sets the extent of paste rol recovery movement while begining the forward print stroke. The movement is measured rearward from the print stroke start position. Mini…

Parameter Definition

Image Y Justification This parameter defines the position of the image about the Image Y

parameter. The image can be front, rear or centre justified about Image Y.

Options are:

Front; Rear; Centre.

Default Centre

Barcode Y This parameter defines the dimension between the centre of the barcode to the

outer rear edge of the screen frame or adaptor.

Minimum 10mm

Maximum Screen Length - 10mm

Increment 0.1mm

Default 97mm

Front Knead Speed This parameter sets the speed of kneading in the forward direction

Minimum 2mm/sec

Maximum 150mm/sec

Increment 1mm/sec

Default 10mm/sec

Rear Knead Speed This parameter sets the speed of kneading in the rearward direction.

Minimum 2mm/sec

Maximum 150mm/sec

Increment 1mm/sec

Default 10mm/sec

Front Knead Pressure This parameter sets the pressure to be applied, while using squeegees, when

kneading in the forward direction.

Minimum 0kg

Maximum 20kg

Increment 0.2kg

Default 5kg

Rear Knead Pressure This parameter sets the pressure to be applied, while using squeegees, when

kneading in the rearward direction.

Minimum 0kg

Maximum 20kg

Increment 0.2kg

Default 5kg

ProFlow Knead Pressure This parameter sets the pressure to be applied, while using ProFlow, when

kneading in either direction.

Minimum 0kg

Maximum 20kg

Increment 0.2kg

Default 10kg

Paste Recovery Rate This parameter sets the frequency, measured in print strokes completed in

either direction, at which paste roll recovery occurs in both directions, when

using squeegees.

Minimum 0 (This disables paste roll recovery)

Maximum 500

Increment 1

Default 1

Front Paste Recovery This parameter sets the extent of paste roll recovery movement while

begining the rearward print stroke. The movement is measured forward from

the print stroke start position.

Minimum 0mm

Maximum 15mm (Subject to the front turnaround

envelope)

Increment 1mm

Default 5mm

Software Version 6 User Manual 1.105

MACHINE PROGRAMMING

MENU PARAMETERS

Parameter Definition

Rear Paste Recovery This parameter sets the extent of paste rol recovery movement while begining

the forward print stroke. The movement is measured rearward from the print

stroke start position.

Minimum 0mm

Maximum 15mm (Subject to the rear turnaround

envelope)

Increment 1mm

Default 5mm

Tooling Deviation This parameter sets the extent of tooling deviation before a warning message

is posted.

Minimum 0%

Maximum 50%

Increment 0.25%

Default 20%

1.106 User Manual Software Version 6

MACHINE PROGRAMMING

MENU PARAMETERS

SPC CONFIGURATION

Whenthe cursor on the EditCurrent Process Parameterspage highlightsthe SPC

Configuration option and Incr. or Decr. are pressed an SPC Configuration

Window opens and two extra menu options become available:

Configuration

Window

Theconfiguration window allows the user to setup the MachinesSPCoperation.

Data Output Rate Two rates of data output are available as follows:

Every Cycle - Outputs SPC data every cycle except for the camera data, which is

output dependant upon the settings of the parameters start rate, sample rate and

start rate limit.

On Inspect - Outputs all SPC data at a rate dependant upon the settings of the

parameters start rate, sample rate and start rate limit.

Start Rate Sets the initial SPC output rate, for setting up a line. If start rate is set to 10, SPC

data is output every 10 cycles until the start rate limit is reached, when the rate

becomes that set in the sample rate parameter. The range is 1-100.

Sample Rate Sets the rate of SPC output after the start rate limit has been reached. The range

is 0-100, where 0 = use start rate until start rate limit is reached. If sample rate is

setto 15, SPC data is output every 15cyclesafterthestartrate limit is reached.

Start Rate Limit Sets the amount of SPC output cycles at the start rate. When this limit is reached

the sample rate parameter becomes the active SPC output rate. The range is

0-100, where 0 = continuous SPC output at the start rate.

NOTE

Setting both start rate limit and sample rate to zero causes continuous SPC

output at the start rate.

Software Version 6 User Manual 1.107

MACHINE PROGRAMMING

SPC CONFIGURATION

SPC Configuration Page.

DATA OUTPUT RATE

START RATE

SAMPLE RATE

START RATE LIMIT

SPC DATA MODE

SPC FORMAT

UPDATE ON START-UP

ALIGN INSPECT MODE

EVERY CYCLE

SERIAL

WINDOWS

PRE PRINT

cycles