Dek-265GSX-User-Manual.pdf.pdf - 第282页

Edit Global 1. Select Edit Global . Edit Global NOTE Delete site is only available if at least one site exists already. Next site and previous site are only available if at least two sites exist already. 2. Enter the par…

17.

Select Run.

Run

18.

If the screen has not been changed the message ‘Screen has not been

changed for this product’ is displayed, select Use Screen to continue.

19.

Select Auto Board.

Auto

Board

20.

The message ‘Load board’ is displayed. Load board, select Confirm when

the board is loaded.

Confirm

21. Setup the board and screen fiducials.

22.

Select Inspect Setup. If this option is unavailable, check set prefs for 2D

Inspection enabled.

Inspect

Setup

NOTE

The windows in this procedure show the parameters and options available with

both screen and board inspect type set to advanced. If screen or board inspect

type is set to basic or none, certain parameters and options are not displayed.

CAUTION

FIDUCIAL POSITION. If during the print cycle, the position of board

fiducials are changed, the position of previous inspection sites (if any) may

be affected. Small changes are automatically compensated for, however

large changes, ie more than 3mm, require sites to be repositioned.

Software Version 6 User Manual 8.17

2Di INSPECTION

2Di SETUP

2D INSPECT RATE

STENCIL INSPECT TYPE

BOARD INSPECT TYPE

PRE-IMAGE

MIN SITES/CYCLE

WARNING LIMIT

BLOCKAGE ACTION

BLOCKAGE CLEAN

SMEAR ACTION

SMEAR CLEAN

LOW PASTE ACTION

INSPECTAFTER CLEAN

POST PRINTALIGNMENT

No. SITES

ADVANCED

EVERY

MANUALACTION

MODE 1

MANUALACTION

MODE 2

RE-PRINT

ENABLED

PERFORMED

Global Inspect Parameters

SITE NAME

SITE PRIORITY

STENCIL INSPECT TYPE

BOARD INSPECT TYPE

SITE ALIGNMENT

LIMIT SITE I.D.

PASTE SCALING

SITE X COORD

SITE Y COORD

SITE WIDTH

SITE HEIGHT

QFP 1

GENERAL

ADVANCED

X AND Y

FINE

1.00

84.5 mm

89.5mm

4.00 mm

Site Parameters

Edit Global 1.

Select Edit Global.

Edit

Global

NOTE

Delete site is only available if at least one site exists already.

Next site and previous site are only available if at least two sites exist already.

Enter the parameter values below using the Next, Previous, Incr. and Decr.

keys.

Next Previous Incr. Decr.

• Pre-image to Every

• Min Sites to 10

• Warning Limit to 20, this can be reduced later in ‘adjust inspect’.

• Blockage Action to Manual,this canbechangedlaterin ‘adjust inspect’.

• Smear Action to Manual, this can be changed later in ‘adjust inspect’.

A definition of all 2Di parameters and their values is given at the end of this

chapter.

On completion of successful setup, parameters can be adjusted to suit the

product.

Select Limit Options.

Limit

Options

8.18 User Manual Software Version 6

2Di INSPECTION

2Di SETUP

Advanced

Every

Manual

Mode 1

Manual

Mode 2

Manual

Enabled

Performed

Stencil Inspect Type

Board Inspect Type

Pre-image

Min. Sites/Cycle

Warning Limit

Blockage Action

Blockage Clean

Smear Action

Smear Clean

Low Paste Action

Inspect After Clean

Post Print Alignment

Edit Global Parameters

These are usually set to enabled. If for any reason a particular inspection is not

required, set to disabled. If any global limit options are disabled the

corresponding limit sets and parameters are greyed out. These are global limits,

therefore they are active for the whole product. If a particular inspection is not

requiredfor a specific type of site, this can beachievedlaterinlimit set options.

Enter global limit options using Next, Previous, Incr. and Decr. keys.

Next Previous Incr. Decr.

Select Exit.

Exit

Select Exit.

Exit

Edit Limits 1.

Select Edit Limits.

Edit

Limits

The following window is displayed:

Software Version 6 User Manual 8.19

2Di INSPECTION

2Di SETUP

Enabled

Blockage

Smear

Paste

Alignment

Bridging

Volume

Global Limit Set Options

Default

10%

15%

0.01 sq mm

0.15 sq mm

90%

80%

0.02mm

0.03mm

0.05mm

0.04mm

80%

70%

LimitSetID

BlockageWarning

BlockageAlarm

SmearWarning

SmearAlarm

PasteWarning

PasteAlarm

AlignWarning

AlignAlarm

BridgeWarning

BridgeAlarm

VolumeWarning

VolumeAlarm

LimitSets

LimitParameters