00196608-01_AI_Stationaere_Kamera_Typ33_36_de_en.pdf - 第101页
Brief Description Version Overview Prerequisites and Restrictions Stationary Camera Typ e 33/36 Stationäre Kamera Typ 33/36 101 2.2 Prerequisites and Restrictions ▪ Type 33 stationary cameras ca n be used in the SX serie…
Brief Description
Product Description Technical Data.
100 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
2.1.1 Technical Data.
2.1.1.1 Component Camera, Stationary, P&P (Type 33) 55x45
The "component camera stationary P&P (type 33) 55x45" provides a resolution of 41 µm and a wider
available component spectrum of up to 55x45 mm. This stationary camera can, for example, be ordered
if you require greater resolution or when you need to place multiple components which are larger than
the field of view supported by your standard camera. For more information about this data, refer to the
specification documents for the relevant placement head or for the standard camera.
2.1.1.2 Component Camera, Stationary, P&P (Type 36) 32x32
The placement accuracy of the "component camera stationary P&P (type 36) 32x32" is specific to the
machine and head used. For more information about this data, refer to the specification documents for
the relevant placement head or for the standard camera.
2.1.2 Version Overview
Component dimensions 0.5 mm x 0.5 mm up to 55 mm x 45 mm
Component spectrum 0402, MELF, SO, PLCC, QFP, electrolytic capaci-
tors, BGA
Min. lead pitch 0.30 mm
Min. lead width 0.15 mm
Min. ball pitch 0.35 mm
Min. ball diameter 0.20 mm
Field of view
65x50 mm
2
Method of illumination Front-lighting (6 levels, programmable as re-
quired)
Component dimensions 0.8 x 0.8 mm ｲ to 32 x 32 mm ｲ (simple measure-
ment)
Component spectrum 0603, MELF, SO, PLCC, QFP, electrolytic capaci-
tors, BGA
Min. lead pitch 0.40 mm
Min. lead width 0.24 mm
Min. ball pitch 0.56 mm
Min. ball diameter 0.32 mm
Field of view
38x38 mm
2
Method of illumination Front-lighting (6 levels, programmable as re-
quired)
Version
SST33
Version
SST36
Description
01, 02 --- Without CAN controller, VCU required (CAN and power supply via VCU)
03 to 06 01 With CAN controller (as TQ module), VCU not required, 8 pin DIP switch on the
driver board
From 06 From 04 Simpler assembly with key holes
From 07 From 05 With CAN controller (integrated on the board), VCU not required, 6 pin DIP switch
on the driver board
Brief Description
Version Overview Prerequisites and Restrictions
Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 101
2.2 Prerequisites and Restrictions
▪ Type 33 stationary cameras can be used in the SX series, X series, D3 and D1 machines.
▪ Type 36 stationary cameras can only be used in D1 machines.
▪ The camera design and the assembly procedure for each camera is generally the same for the indi-
vidual machines. Any differences will be explicitly indicated in this guide.
▪ When using a C&P20 head, make sure that there are no stationary cameras fitted in the same place-
ment area.
▪ When using X series or SX series machines, you may need to move the COT insert, depending on
your machine configuration.
▪ A type 33 stationary camera of version 1 or 2 can only be used in X series machines up to number
326.
From version 3, it can also be used with SIPLACE D series, SX and X series machines of number
326 or higher.
▪ When fitting the camera in an X series or SX4 machine, you will need to have two hotlink cards in
the box PC.
WARNING
Head crash risk by changeover to C&P20 head
When changing the placement head from a TwinHead or CPP to a C&P20, you will need to dis-
mantle all stationary component cameras (stationary P&P, type 33, 55x45, and type 25, 16x16)
from the TwinHead.
If this is not done, there is a risk that the C&P20 head could crash with the camera housing.
WARNING
Head crash by changeover to CPP head
When changing the placement head from a TwinHead to a CPP, you will need to install the sta-
tionary component camera (type 33, 55x45, digital) in the lower position.
Brief Description
Scope of Delivery SIPLACE X Series, D3
102 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
2.3 Scope of Delivery
Depending on your machine, you may need one of the following installation kits:
2.3.1 SIPLACE X Series, D3
Installation kit: stationary camera type 33 for CPP head fitted in X series [00119782-xx]
2.3.2 SIPLACE D1
The P&P module in the SIPLACE D1 is supplied in its default configuration with a component camera
stationary P&P (type 36) 32x32 digital [03042491-xx]. This is also included in the delivery package for
the HRK P&P module for SIPLACE D1 machines.
Installation of the camera is the same as that for the stationary camera described here (type 33) 55x45
digital.
Installation kit: stationary camera (type 33) 55x45 digital in the D1
To convert a D1 for the "component camera stationary P&P (type 33) 55x45", you only need the camera
itself as all attached parts of the "component camera stationary P&P (type 36) 32x32 digital" can still be
used.
Quantity Designation Item No.
1 Component camera, stationary, P&P (type 33) 55 x 45, digital 03016339- xx
1 Sandwich plate for fiducial complete – L600 03022077- xx
4 ISO4762 - M6x35-8.8, galvanized, DSP8 03069136- xx
2 DIN913-M6x50-ST 03005958- xx
1 CAN bus: IC camera 03050239- xx
1 Waste box for TwinHead 03003047- xx
1 Fixture plate for waste box 03003048- xx
2 ISO4762 - M6 x 12-A2-70 03042572- xx
1 Assembly instructions "stationary camera type 33/36" DE+EN 00196608- xx
1 Reject bin sensors for upgrade 03079029- xx
Quantity Designation Item No.
1 Component camera, stationary, P&P (type 33) 55x45, digital 03016339- xx
2 DIN913-M6x50 (set screws) 03005958- xx
NOTICE
Same parts for camera type 33 in D1 as required for camera type 36
For the D1 you can use the same screws and "sandwich plate for fiducial IC camera"
[03039370-xx] as were used for the type 36 stationary camera.
The "component reject assembly for P&P head" [03047406-xx] remains in the machine.