00196608-01_AI_Stationaere_Kamera_Typ33_36_de_en.pdf - 第122页
Installation Installation on X Series and D3 Machines Electrical Connections 122 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/ 36 ► Set the DIP switch on the "Contr ol Unit 1 Vision, Stationary" [ 0036…
Installation
Electrical Connections Installation on X Series and D3 Machines
Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 121
VCU without CAN bus and without TQM module
* Cameras with FS03 already have a CAN controller fitted. These cameras therefore do not need a VCU.
However, for reasons of downwards compatibility, you can still connect this type of camera to machines
with a VCU. To do this, you will need the "camera power adapter cable" [03059912-xx].
1 "Control Unit 1 Vision, Stationary"
[00363961-xx]
2 DIP switch VCU
3 Adapter cable for power to camera
[03059912-xx] *
4 PA1 subdistributor
Cable Vision Control IC camera 1
[03003449-xx]
to subdistributor (X4rd)
PA2 main distributor
Cable Vision Control IC camera 2
[03003439-xx]
to main distributor (X4rd)
5 PA1 subdistributor
Cable Vision Control FC camera 1
[03003450-xx]
to subdistributor (X5rd)
PA2 main distributor
Cable Vision Control FC camera 2
[03003440-xx]
to main distributor (X5rd)
6 Cable: Voltage supply "Control Unit 1 Vi-
sion, Stationary" (X3rd)
Installation
Installation on X Series and D3 Machines Electrical Connections
122 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
► Set the DIP switch on the "Control Unit 1 Vision, Stationary" [00363961-xx]:
Subdistributor: 5 and 6 to ON and the others to OFF
Main distributor: 6 to ON and the others to OFF
► If present, disconnect the CAN bus cable (X2) from the "Control Unit 1 Vision, Stationary"
[00363961-xx].
► If present, remove the existing TQM module [03003536-xx] from the VCU [00363961-xx].
► Insulate the CAN bus cable with adhesive tape and fix this to the cable tree. This is needed to prevent
interference.
► If not already connected, plug in the voltage supply cable "Control Unit 1 Vision, Stationary" (6).
► Plug in the "camera power adapter cable" (3) [03059912-xx] between the "Control Unit 1 Vision, Sta-
tionary" (X4 or X5) [00363961-xx] and the black Vision control cable (4) and (5). See also the circuit
diagrams "4.4.1.2 Camera From FS03" [ ➙ 160].
See also
4.4.1 Up To Machine Series No. B325 [ ➙ 159]
S1 Setting for placement area* Comments
1
(Sub)
2
(Main)
1 -- OFF -- OFF CAN terminator
2 -- OFF -- OFF Reset
3 -- OFF -- OFF Boot
4 -- OFF -- OFF CAN error switch
5ON -- -- OFF ID 1
6ON -- ON -- ID 2
7 -- OFF -- OFF CAN speed
8 -- OFF -- OFF CAN group
CAUTION
You must remove the CAN bus cable!
If you do not remove this cable, this could lead to CAN bus interference.
Installation
Electrical Connections Installation on X Series and D3 Machines
Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 123
3.2.3.3 Connecting the Hotlink Cable to the Computer Unit
► Connect your camera cable to the hotlink cards as follows:
NOTICE
Observe the machine serial number
Observe this section for X series and D3 machines up to serial number B325. These machines
were supplied with a computer unit.
An exception to this are X series machines which have been upgraded to CPP with SW70x. In
these machines the computer unit has been replaced with a box PC.
CAUTION
Never connect a LAN cable to the hotlink card
This could damage the hotlink card.
NOTICE
Connection for stationary cameras
► Observe section "4 Appendix" [ ➙ 153] and the latest circuit diagrams for your machine.
► The camera cables are labeled with their relevant connection details.
Hotlink cards to the computer unit
1. FC camera for PA1 CAM3 (X3pr)
2. FC camera for PA2 CAM3 (X3ps)
3. IC camera for PA1 CAM2 (X2pr)
4. IC camera for PA2 CAM2 (X2ps)
5. Hotlink cards
To (5) hotlink cards
PA1 - card 1 (left) PA2 - card 2 (right)
CAM0 Gantry 1: PCB/component camera Gantry 2: PCB/component camera
CAM1 Gantry 4: PCB/component camera Gantry 3: PCB/component camera
CAM2 (3) IC camera PA1 → cable X2pr (4) IC camera PA2 → cable X2ps
CAM3 (1) Gantry 4 FC camera → cable X3pr (2) Gantry 3 FC camera → cable X3ps