00196608-01_AI_Stationaere_Kamera_Typ33_36_de_en.pdf - 第149页
Installation Assembling the Camera General Final Work Stationary Camera Typ e 33/36 Stationäre Kamera Typ 33/36 149 3.6 General Final Work The following tasks must be performed irrespective of the machi ne type: 3.6.1 As…
Installation
Installation on SX4 Machines Final Work
148 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
3.5.4 Final Work
► Fit the camera housing. (See also "3.6.1 Assembling the Camera" [ ➙ 149])
► If the reject bin sensor is present (2), you will need to fit this in a new position for the X series ma-
chine. For more information, refer to the relevant assembly instructions:
"Reject Bin Query X series/D3/SX4, DE+EN" [00194716-xx]
"Reject Bin Query SX1/SX2, DE+EN" [00196615-xx]
(See also "3.6.3 Fitting the Component Reject Bin" [ ➙ 150])
► Insert the "reject bin for TwinHead" [03072806-xx].
► Push the COT insert into its original position and screw tightly into place. Read the service manual
for your machine first.
► Hook the waste tape chute back into place.
► Fit the lower side cover. See alsoReplacing the Complete X Series Docking Unit [03015680-xx]
► Remove any objects from the travel range of the gantry and placement head.
► Start the machine and move the component trolley back into the machine.
► Calibrate the machine. (See also "3.6.2 Calibrating the Camera" [ ➙ 150])
Reject bin holder (example of X series shown)
► If not already present, fit the "reject bin holder" (1)
[03063283-xx] with two screws (DIN7984-M6x12-A2-
70) [03081847-xx].
Installation
Assembling the Camera General Final Work
Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 149
3.6 General Final Work
The following tasks must be performed irrespective of the machine type:
3.6.1 Assembling the Camera
► Fit the housing for the lower section of the camera. This is either screwed or hooked into place, de-
pending on your camera type.
► Carefully place the camera upper section (illumination unit) on the camera lower section. Make sure
that the camera upper section is pushed in as far as the stop.
► Make sure that the glass surface is clean. Clean the mirror and glass surface with a microfiber cloth,
if necessary.
1. Camera upper section (illumination unit)
2. Camera lower section
3. Glass sheet
4. Camera electronics
5. Openings for fastening screws
NOTICE
The upper section of the camera has a fixed assignment to the bottom section of the camera!
The upper section of the camera may not be used with a different bottom section. Both the up-
per and lower sections are mechanically and electrically coordinated and may not be ex-
changed for use with other cameras. The serial and version numbers of the top and bottom
sections of the camera must be identical.
Installation
General Final Work Calibrating the Camera
150 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
3.6.2 Calibrating the Camera
Calibrating the camera (SR70x.xx)
► Switch over to the operator level Machine service.
► Select Service (configure, update and calibrate the machine) --> Machine calibration.
► Select Head and cameras and click on Next.
► Select the relevant Gantry and click on Next.
► In the next step, the preconditions are checked. If these are fulfilled, click on Start.
Calibrating the camera (SR60x.xx)
► Start SITEST and perform camera calibration. See also the software guide for SITEST.
Firmware Download
3.6.3 Fitting the Component Reject Bin
When using the "stationary camera for CPP head" option, you need to fit an additional reject bin for com-
ponents > 36x36 mm. This is identical to the TwinHead reject bin.
This reject bin is included in the delivery packages for the stationary camera and the HRK for TwinHead.
Overview
NOTICE
Firmware download for cameras with 6-pin DIP switch (type 33 from version 07, type 36 from
version 05) and station software below 605.xx
The station software below 605.xx does not support the firmware download to these cameras.
SITEST shows a red cross in the relevant menu. However, the camera is still fully functional.
The red cross can be ignored.
Holder for component reject bin (X series)
1. Holder for reject bins
2. Sensor for the component reject bin (optional)