00196608-01_AI_Stationaere_Kamera_Typ33_36_de_en.pdf - 第116页

Installation Installation on X Series and D3 Machines Electrical Connections 116 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/ 36 Connection to the Vision Control Unit Stationary Up To Serial Number B325 and IC …

Installation

Electrical Connections Installation on X Series and D3 Machines

Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 115

See also

 3.2.3.3 Connecting the Hotlink Cable to the Computer Unit [ ➙ 123]

Camera (FS02)

1. X5: Vision cable 34-pin, from IC camera to Vision

Control Unit, stationary

2. X3: Cable from camera bus to computer unit

► Connect the cable (1) to the camera. This creates the

connection to the Vision Control Unit, stationary.

► Connect the cable (2) to the camera. This creates the

connection to the computer unit. Continue by reading

the following section: "3.2.3.3 Connecting the Hotlink

Cable to the Computer Unit" [ ➙ 123]

For more information, refer to the circuit diagrams:

"4.4.1.1 Camera Up To FS02" [ ➙ 159]

Vision LED driver board SST20 (up to FS02)

1. X2: Not relevant

2. X3: Cable from camera bus to computer unit

3. X4: Jumper must be connected

4. X5: Vision cable 34-pin, from IC camera

[03003439-xx] to Vision Control Unit, stationary

5. X3: Not relevant

Installation

Installation on X Series and D3 Machines Electrical Connections

116 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36

Connection to the Vision Control Unit Stationary Up To Serial Number B325 and IC Camera FS01 and

FS02

NOTICE

Observe the machine serial number and camera FS number.

Observe this section for X series machines up to serial number B325 and IC cameras with FS01

or FS02.

NOTICE

CPP and VCU

The Vision Control Unit (VCU) does not support CPP heads. CPP heads and the corresponding

stationary cameras are therefore only possible from machine serial number B326.

► In this case, read the corresponding assembly instructions for information about further re-

strictions.

NOTICE

TQM module

The TQM module [03003536-xx] is not part of the camera delivery package and will need to be

ordered separately if required.

NOTICE

Control Unit 1 Vision, Stationary [00363961-xx]

The "Control Unit 1 Vision, Stationary" [00363961-xx] is part of the "Reconfig. parts kit parts kit

for X series/TwinHead" [03041487-xx].

VCU

► Connect the TQM module to the "Control Unit 1 Vi-

sion, Stationary" [00363961-xx] board.

► Fit the "Control Unit 1 Vision, Stationary" [00363961-

xx] with the connected "TQM167 SIPLACE embed-

ded module" [03003536-xx] in the relevant slot (1).

▪ The VCU for PA1 is located in the subdistributor (lo-

cation 4).

▪ The VCU for PA2 is located in the main distributor (lo-

cation 2).

Installation

Electrical Connections Installation on X Series and D3 Machines

Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 117

VCU with CAN bus and TQM module

► Connect the CAN bus (3) to X2.

► Connect the voltage supply cable for the "Control Unit 1 Vision, Stationary" (6).

NOTICE

BIOS and eSW version

After starting the machine, check the BIOS and Vision system application versions and, if nec-

essary, update the system with a software download.

1 TQM module [03003536-xx] on

"Control Unit 1 Vision, Stationary"

[00363961-xx]

2 CAN bus cable (X2rd)

3 DIP switch VCU

4 PA1: Subdistributor

Cable vision control IC camera 1

[03003449-xx]

To subdistributor (X4rd)

5 PA1: Subdistributor

Cable vision control FC camera 1

[03003450-xx]

To subdistributor (X5rd)

PA2: Main distributor

Cable vision control IC camera 2

[03003439-xx]

To main distributor (X4rd)

PA2: Main distributor

Cable vision control FC camera 2

[03003440-xx]

To main distributor (X5rd)

6 Cable: Voltage supply "Control Unit 1 Vi-

sion, Stationary" (X3rd)