00196608-01_AI_Stationaere_Kamera_Typ33_36_de_en.pdf - 第125页

Installation Electrical Connections Installation on X Series and D3 Machines Stationary Camera Typ e 33/36 Stationäre Kamera Typ 33/36 125 Hotlink card (PCI-A24 [03052135-xx]) The hotlink car d is installed as a default …

100%1 / 172
Installation
Installation on X Series and D3 Machines Electrical Connections
124 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
3.2.3.4 Connecting the Hotlink Cable to the BoxPC
In the SIPLACE X4, two types of hotlink cards can be fitted. When installed, these can only be differen-
tiated from the PCI-A14 by looking at the order of camera input connections. See the following diagrams
for an illustration of this.
► Connect your camera cable as follows:
NOTICE
Observe the machine serial number
Observe this section for X series machines from serial number B326. These machines were
delivered with a box PC.
In addition, this applies to X series machines up to serial number B325 which have been up-
graded to CPP with SW70x. In these machines the computer unit has been replaced with a box
PC.
CAUTION
Never connect a LAN cable to the hotlink card!
This could damage the hotlink card.
NOTICE
Connection for stationary cameras
► Observe section "4 Appendix" [ ➙ 153] and the latest circuit diagrams for your machine.
► When installed, the version of your hotlink card can only be determined by the position of
the camera connection label and the order of CAM connections.
► The stationary cameras are always connected to CAM2 or CAM3.
► The camera cables are labeled with their relevant connection details according to the pat-
tern X*p*.
CAUTION
Correctly connecting the camera cable
► Make sure that you connect the cameras correctly. Observe the labels on the hotlink cards
and therefore the type of hotlink card used. If you do not observe this, placement perfor-
mance may be adversely affected.
Pay particular attention to the different order of connections on the PCI-A24!
Hotlink card (PCI-A14 [03032343-xx])
The hotlink card is installed as a default with the box PC
627 up to approx. machine serial number B1125.
When installed, the version of the hotlink cards can only
be seen on the label for the camera connections (5).
(1) and (3): Stationary cameras for placement area 1
(X2pr and X3pr)
(2) and (4): Stationary cameras for placement area 2
(X2ps and X3ps)
Installation
Electrical Connections Installation on X Series and D3 Machines
Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36 125
Hotlink card (PCI-A24 [03052135-xx])
The hotlink card is installed as a default with the box PC
627B up to approx. machine serial number B1125. in
principle, the use of a hotlink card is possible from
SW605.03 (e.g. as spare part).
When installed, the version of the hotlink cards can only
be seen on the label for the camera connections (5).
(1) and (3): Stationary cameras for placement area 1
(X2pr and X3pr)
(2) and (4): Stationary cameras for placement area 2
(X2ps and X3ps)
Hotlink cards
PA1
Card 1 (top)
PA2
Card 2 (bottom)
CAM0 Gantry 1 - PCB/component camera Gantry 2 - PCB/component camera
CAM1 Gantry 4 - PCB/component camera Gantry 3 - PCB/component camera
CAM2 Gantry 1 - stationary cameras (IC/FC)
→ Cable X2pr
Gantry 2 - stationary cameras (IC/FC)
→ Cable X2ps
CAM3 Gantry 4 - stationary cameras (IC/FC)
→ Cable X3pr
Gantry 3 - stationary cameras (IC/FC)
→ Cable X3ps
Installation
Installation on X Series and D3 Machines Final Work
126 Stationary Camera Type 33/36 Stationäre Kamera Typ 33/36
3.2.4 Final Work
► Fit the camera housing. See also: "3.6.1 Assembling the Camera" [ ➙ 149]
► Fit the "reject bin holder" and the corresponding sensors. See also: "3.6.3 Fitting the Component Re-
ject Bin" [ ➙ 150]
► Push the COT insert into its original position and screw tightly into place. Read the service manual
for your machine and section "3.2.4.1 COT Insert Assembly" [ ➙ 126] for more information.
► Hook the waste tape chute back into place.
► Fit the lower side cover by following the instructions in the reverse order, as described at Replacing
the Complete X Series Docking Unit [03015680-xx].
► Make sure that there are no objects in the hazard area of the gantry and remove any which are.
► Start the machine and move the component trolley back into the machine.
► Calibrate the machine. See also: "3.6.2 Calibrating the Camera" [ ➙ 150]
3.2.4.1 COT Insert Assembly
If you have moved the COT insert, fit it back into its original position and fit the side covers. Proceed as
follows:
► Move the COT insert into its final position (to the previously marked installation position).
Take care not to damage the cables and hoses.
► Loosely screw in the fitting screw and the fastening screws.
► Tighten the fitting screw first.
► Tighten the five fastening screws.
► Fit the side cover.
CAUTION
Service manual
► Read the section "Replacing the COT Insert" in your service manual!
CAUTION
Observe the specified order!
The fitting screw must be tightened first.