SI-F130 Manual(EN)_jpg_ Rev1.pdf - 第108页
Adjustment of H Axis Lower End OT Sensor (H-CW) HLF-10405-01 Adjustment of H A xis Low er End OT Sensor (H-CW) SHEET 1/2 Adjustment of H Axis Lower End OT Sensor (H-CW) [Necessary jigs] • H axis sensor adjusting jig (L=1…
Adjustment of H Axis Upper End OT Sensor (H-CCW)
HLF-10404-01
Adjustment of H Axis Upper End OT
Sensor (H-CCW)
SHEET
3/3
9 Input the H axis offset value.
1. Click in an order of ORG OFFSET tab
ÎChange Offset button.
Offset screen is displayed.
2. Input a value into the H Offset box so
that the gap between the upper end of
the inner shaft and the H axis pusher
should be 0.05 mm.
3. Click the Set button.
Offset value for the H axis is set.
Adjustment of H Axis Lower End OT Sensor (H-CW)
HLF-10405-01
Adjustment of H Axis Lower End OT
Sensor (H-CW)
SHEET
1/2
Adjustment of H Axis Lower End OT Sensor (H-CW)
[Necessary jigs]
• H axis sensor adjusting jig
(L=15.5 mm, 15.0 mm)
[Procedure]
1 Move the inner shaft of the turret No.1 to
right below the H axis pusher.
2 Install the H axis sensor adjusting jig to the
inner shafts of turret No.1.
1. Push the H axis pusher from the upper
by hand, and push down the inner
shaft.
2. Pinch the H axis sensor adjusting jig
(L=15.5 mm) between the turret and
inner shaft.
3. Remove the cap screw for H axis sen-
sor adjusting jig.
3 Turn off the H axis servo.
1. Click in an order of M/C SETUP menu
ÎORG OFFSET tabÎ R.H button.
RN/H Axis screen is displayed.
2. Click the servo OFF button for H axis.
Servo for H axis is turned off.
H axis sensor adjusting jig
15.5 mm 15 mm
H axis sensor
adjusting jig
Cap screw
Adjustment of H Axis Lower End OT Sensor (H-CW)
HLF-10405-01
Adjustment of H Axis Lower End OT
Sensor (H-CW)
SHEET
2/2
4 Loosen the cap screws (2-M3) on sensor
bracket for the H axis lower end OT sensor
to move the bracket downward (to lower
end).
The LED for H axis lower end OT sensor lights up.
• Keep the cap screws (2-M3) in temporar-
ily tightened state.
• When the H axis lower end OT sensor is
obstructed, the LED lights up.
5 Move the sensor bracket for the H axis lower end OT sensor upward little by little, tighten the cap
screws (2-M3) at a position of boundary where the lighting LED extinguishes, and secure the sensor
bracket.
6 Change the H axis sensor adjusting jig in-
stalled on the inner shaft of the turret No.1 to
a jig of 15.0 mm.
7 Check that the lighting LED for the H axis
lower end OT sensor extinguishes at this time.
Sensor setting: Dark ON
Jig used State of LED
Jig 1 (L = 15.5 mm) Lights-up
Jig 2 (L = 15.0 mm) Extinguish
8 When raising and lowering the dog for the H axis sensor, check that the H axis upper end OT sensor
does not interfere with the ORG sensor cable.
9 Return the H axis servo back to on.
1. Click the servo ON button for H axis
on the RN/H Axis screen.
Servo for H axis is turned on.
2. Click the Return button to close the
RN/H Axis screen.
Sensor bracket
Cap screw
H axis lower end OT sensor
H axis sensor
adjusting jig
Cap screw