编带机说明书-含图纸tm401.pdf - 第81页
D292104.7a.fm Nozzle Installation Chapter 4: Setup 4- 7 Nozzle Installation The TM-401’ s is shipped with the following nozzle s and nozzle tips: • (1) Quad Nozzle Shank • (1) Small Precision T ool (SPT) Nozzle Shank • (…
4-6 TM-401 User’s Guide
Load the Manual Tube Input Device (MTID) D292104.7a.fm
3. Load the Manual Tube Input Device (MTID)
with tubes.
The maximum number of tubes that can be
loaded is determined by the size of the
tubes that are loaded.
The minimum number of tubes is one.
Note: The TM-401 is designed to work with
one or two MTIDs. If two MTIDs were
included with this TM-401, install them both
at this time.
4. Turn the Vibratory ON
5. Adjust the Vibratory Frequency (speed)
and Amplitude (strength) Controls as
needed. Parts should feed fluidly but not
so rapidly that it causes parts to begin
jumping around.
Step 3:
Setup
MTID
Downloaded from www.Manualslib.com manuals search engine
D292104.7a.fm Nozzle Installation
Chapter 4: Setup 4- 7
Nozzle Installation
The TM-401’s is shipped with the following nozzles and nozzle tips:
• (1) Quad Nozzle Shank
• (1) Small Precision Tool (SPT) Nozzle Shank
• (1) Convum Nozzle Shank
• (1) Large Quad Vacuum Cup
• (1) Medium Quad Vacuum Cup
• (1) Small Quad Vacuum Cup
• (1) SPT Vacuum Cup
• (1) Convum Vacuum Cup
• (2) O-Rings
Note: Nozzle Tips are available in a wide range of sizes and style. Contact V-TEK
Service for information on ordering additional Nozzle Tips.
Selecting the Correct Nozzle & Nozzle Tip
To achieve the best picking results, select the largest cup size the part can accommo-
date. Maximizing the cup size gives the vacuum access to more surface area which
increases its pick-up capability. The goal is to use a nozzle cup that is just slightly smaller
than the part being picked.
The Convum bellows-style cups have a flexible flange that are useful for picking irregular
or heavy parts.
Step 4:
Nozzle
Installation
SELECT
NOZZLE
Convum Quad SPT
Downloaded from www.Manualslib.com manuals search engine
4-8 TM-401 User’s Guide
Nozzle Installation D292104.7a.fm
Installing Nozzle & Nozzle Tip
1. Move the Pick & Place Head to the Place position
so it is easily accessible from the front. .
2. Remove the air line from the Nozzle Shank, sup-
porting the Nozzle with one hand while gently pull-
ing the tube off the Nozzle Barb.
3. Using a 2mm Hex wrench, loosen the set screw
that retains the Nozzle Shaft.
4. Slide the Nozzle Shank down and remove it from
the Pick & Place Assembly. Store the unused
Nozzle Shank and Nozzle Cup in the Spare Parts
Kit.
5. Select the correct Nozzle Shank and Nozzle Cup
for the part that will be run. Press the Nozzle Cup
onto the Nozzle Shaft.
6. Insert the Nozzle Shank into the Actuator Shaft in
the Pick & Place Assembly.
Note: When positioning the Nozzle Shank,
push it all the way up to the Actuator Shaft,
then pull it back slightly (about 1mm) so the
body of the Nozzle Shank doesn’t rub the body
of the Actuator.
7. Using a 2mm Hex wrench, tighten the set screw to
retain the Nozzle Shaft..
8. Re-attach the air line to the Nozzle Barb.
Step 4:
Nozzle
Installation
SELECT
NOZZLE
Downloaded from www.Manualslib.com manuals search engine