4OM-1625-004_w.pdf - 第126页

4OM-1603 2-7 2. Management Information : Chap.2 Management Information Code Display Area A (The outline of the Management Information) Display Area B (The details of the Management Information) 014b01 Nozzle Placement Da…

100%1 / 347
4OM-1603
2-6
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
011706
P.C.B. position
Please position P.C.B. [Output position] of [Lane A].
011707
P.C.B. position
Please position P.C.B. [Input position] of [Lane A].
011708
P.C.B. position
Please position P.C.B. [Input or Output] of [Lane B].
011709
P.C.B. position
Please position P.C.B. [Output position] of [Lane B].
01170a
P.C.B. position
Please position P.C.B. [Input position] of [Lane B].
011a01
Nozzlestockerlowerlimitconrmation
Please perform All zeroing.
011c01
Nozzlearrangementconrmation
The nozzle arrangement of the Current Program and the head is different.
012a01
Tray shortage Comp (rear)
Please supply comp, close tray door(rear) and push tray ready SW(Rear).
012b01
Tray shortage Comp (front)
Please supply comp, close tray safety door and push tray ready SW(Front).
013101
Feeder set Err
A pickup miss comp is detected. (Rear)
013102
Feeder set Err
The feeder latch worked off. (Rear)
013103 Feeder set Err
A pickup miss comp is detected. (Front)
013104 Feeder set Err
The feeder latch worked off. (Front)
013105 Feeder set Err
Not connect selected feeder.
013b01 Feeder Ready SW
Please wait stage ready on
013c01 Stage Ready SW
Please wait feeder ready on
013c02 Stage Ready SW
Do not open safety cover while line sensor program updating.
014101 Operation Parameter
Test mode of transfer set ""Disable"" in pass mode.
Check setting.
014102 Operation Parameter
-----
014103 Operation Parameter
-----
014201 Device System Setup
Please set Input Machine Output Mode [SMEMA Mode].
014202 Device System Setup
Please set Output Machine Output Mode [SMEMA Mode].
1012-005
4OM-1603
2-7
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
014b01 Nozzle Placement Data Check
Set the nozzle ID to use for the No.1 nozzle placement data.
015001 Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015002
Nozzle Location Check
"Notfoundttingnozzleforcalibration.(Front)
Set type "HA09A" nozzle on Head 2 Nozzle 1.
015003
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015004
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type ""HA09A"" nozzle on Head 2 Nozzle 1.
015005
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
015006
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
015007
Nozzle Location Check
Already set the different type nozzle.(Rear)
Remove it.
015008 Nozzle Location Check
Already set the different type nozzle.(Front)
Remove it.
015009 Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
01500A
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
01500B
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type "VF02" nozzle on calibrate position.
01500C
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type "VF02" nozzle on calibrate position."
01500D
Nozzle Location Check
"Notfoundttingnozzleforcalibration.(Rear)
Set type "HA09A"or "Vf02" nozzle on calibrate position."
01500E
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type "HA09A"or "Vf02" nozzle on calibrate position.
1012-005
4OM-1603
2-8
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
01500F Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015010 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015011 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015012 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015013 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Rear).Pleasesettype"BF02"nozzleinthe
stocker position where nozzle can change.
015014 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Front).Pleasesettype"BF02"nozzleinthe
stocker position where nozzle can change.
015015 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Rear).Pleasesettype"FA04"nozzleinthe
stocker position where nozzle can change.
015016 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Front).Pleasesettype"FA04"nozzleinthe
stocker position where nozzle can change.
015101 Nozzle location teaching, check the position of nozzle on head
Could not found nozzle or Could not inspect nozzle (different type ?).
015102 Nozzle location teaching, check on the position of nozzle on head
Could not found or inspect nozzle (different type ?).
015201 Teaching check the conveyor
No P.C.B. on Conveyor. Please put P.C.B. in.
015202 Teaching check the conveyor
Please set P.C.B. positioning. Please set it again after cancel positioning if P.C.B.
positioning is already done.
015203 Teaching check the conveyor
-----
016001 Tray teaching
Traverse of Tray is not drawn out (Rear). Draw out Traverse.
016002 Tray teaching
Tray Traverse is not drawn out (Front). Draw out Traverse.
016101 Coplanarity Teaching
"Coplanarity Detection" of Test Operation Mode is set "No". Execute it after
cancelling Test Operation Mode.
016201 Coplanarity Test
Please pickup part.
1012-005