4OM-1625-004_w.pdf - 第166页

4OM-1603 3-1 1 3. Error IDs and Remedial Procedures : Chap.3 1012-005 Error ID Error Name, Description, Cause, and Remedy 400942 Servo Alarm The value of variation counter is out of the range Check out the wiring of Orig…

100%1 / 347
4OM-1603
3-10
3. Error IDs and Remedial Procedures : Chap.3
1012-005
Error ID Error Name, Description, Cause, and Remedy
4008E0 Servo Alarm
Over-Regenerative alarm
Drive with blocking tact.
4008E1 Servo Alarm
Overload alarm1
Drive with blocking Tact.
4008E3 Servo Alarm
Absolute position counter warning
Performnoisestrategiesofencoderor
exchangeservoamplier.
4008E4 Servo Alarm
Parameter warning
Check out servo parameter.
4008E6 Servo Alarm
Servo forced stop alarm
EM1,emergencystopinputofServo
amplierisoff.
4008E7 Servo Alarm
Controller emergency stopping warning
outputted emergency stop from Controller.
4008E8 Servo Alarm
No. of Rot dropping warning of Cooling Fan
Exchange the Cooling fan.
4008E9 Servo Alarm
Main circuit off warning
Main circuit is Off.
4008EB Servo Alarm
another axis warning
Error in another axis in the same P.C.B. Please remove the factor of error.
4008EC Servo Alarm
Overload alarm2
Drive with blocking tact.
4008ED Servo Alarm
Output Watt over warning
Driver with blocking Tact.
400911 Servo Alarm
Power drive Error, Over-current
Check out motor wiring or exchange both motor and driver
400921 Servo Alarm
Overload Alarm
Check
outmotorwiringorexchange
bothmotoranddriver.Either,Conrmthat
the blocking exists with cutter pieces.
400931 Servo Alarm
Speed Alarm
Readjust motor gain.
400941 Servo Alarm
multi-cycle Error
Check out the motor wiring or exchange the motor.
4OM-1603
3-11
3. Error IDs and Remedial Procedures : Chap.3
1012-005
Error ID Error Name, Description, Cause, and Remedy
400942 Servo Alarm
The value of variation counter is out of the range
Check out the wiring of Origin sensor. Or, Exchange driver.
400951 Servo Alarm
Power Drive detected temperature error
Ambient Temperature is high. Exchange driver.
400961 Servo Alarm
Sensor Error
Check Motor Encoder wires. Or, exchange the motor.
400962 Servo Alarm
Sensor Error
Check Motor Encoder wires. Or, exchange the motor.
400971 Servo Alarm
high drive Voltage
Insufcient
power.Exchangedriver.
400972 Servo Alarm
Low drive V
oltage
Check out the drive power wiring putted in Driver. Or, check out DC48V.
400991 Servo Alarm
Reading Error on permanent memory
Exchange the driver.
400992 Servo Alarm
Writing Error on permanent memory
Exchange the driver.
400998 Servo Alarm
CPU Error
Exchange the driver.
400999 Servo Alarm
Parameter Error
Conrm
thechangedvalueofParameter
.
400a08 Head Interlock Error
Releasing the brake is impossible during Servo On.
-----
400b01 Feeder preparation complete
A pick up miss comp or disengaged Latch was detected.
Openthesafetycoverandconrm
thatthereisnointerferencewiththehead,and
then, release the ready feeder.
400c01 Nozzle stocker down time out
Nozzle stock unit lower bound detection 1 was not turned on in prescribed time.
Pleaseconrmthelowerbounddetection
1sensorofnozzlestockunit.
400c02 Nozzle stocker down time out
Nozzle stock unit lower bound detection 2 was not turned on in prescribed time.
Pleaseconrmthelowerbounddetection
2sensorofnozzlestockunit.
400c03 Nozzle stocker down time out
Nozzle stock unit lower bound detection 3 was not turned on in prescribed time.
Pleaseconrmthelowerbounddetection
3sensorofnozzlestockunit.
4OM-1603
3-12
3. Error IDs and Remedial Procedures : Chap.3
1012-005
Error ID Error Name, Description, Cause, and Remedy
400c04 Nozzle stocker down time out
Nozzle stock unit lower bound detection 4 was not turned on in prescribed time.
Pleaseconrmthelowerbounddetection
4sensorofnozzlestockunit.
400d01 Software Interlock Error
Head (Rear) NL axis's poor operation was detected, and the scram of the XY axis
was carried out.
Please perform a zeroing.
400d02 Software Interlock Error
Head (Rear) NL axis's poor operation was detected, and the scram of the XY axis
was carried out.
Please perform a zeroing.
400d03 Software Interlock Error
NL axis(Front) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
Please perform a zeroing.
400d04 Software Interlock Error
NL axis(Rear) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
Please perform a zeroing.
400d05 Software Interlock Error
L1 axis(Front) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
PleaseconrmdetectionofPassLine,excesspushing.
400d06 Software Interlock Error
L2 axis(Front) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
PleaseconrmdetectionofPassLine,excesspushing.
400d07 Software Interlock Error
L3 axis(Front) Interlock Detected
PleaseconrmdetectionofPassLine,
excesspushing.
400d08 Software Interlock Error
L1 axis(Rear) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
PleaseconrmdetectionofPassLine,excesspushing.
400d09 Software Interlock Error
L2 axis(Rear) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
PleaseconrmdetectionofPassLine,excesspushing.
400d0a Software Interlock Error
L3 axis(Rear) Interlock Detected.
Pleaseconrmthenozzlehasnot
fallenwhenyoupushthebeambythehand.
PleaseconrmdetectionofPassLine,excesspushing.
400f01 Safety Cover
Safety cover opened
Close the safety cover and lock it.