4OM-1625-004_w.pdf - 第249页
4OM-1603 3-94 3. Error IDs and Remedial Procedures : Chap.3 Error ID Error Name, Description, Cause, and Remedy 49700f On manual operation Alarm System Error System Error of internal driver . Driver error is supposed if …
4OM-1603
3-93
3. Error IDs and Remedial Procedures : Chap.3
Error ID Error Name, Description, Cause, and Remedy
497002 On manual operation Alarm
Out-of-Control was detected.
Motor Out-of-Control which is over the width of Out-of-Control detecting occurred.
Please execute all zeroing again, and the restart production.
Please set motor speed slow if it happens frequently. Also, in a case of structure
motor Error.
497003 On manual operation Alarm
Error in Motor Power voltage
Motor power voltage dropped. Check out the Power supply line(48V Line)
497004 On manual operation Alarm
STP input was detected.
STP input is detected. The function to stop motor by Hard signal.
497005 On manual operation Alarm
Over-current
Error in Motor output line. Check out the motor wiring,
497006 On manual operation Alarm
Limit Sensor(+) was detected.
+LS signal was detected for moving for (+).
Please check the dirt of +LS sensor, disconnection.
497007 On manual operation Alarm
Limit Sensor(-) was detected.
-LS signal was detected for moving for (-).
Please check the dirt of -LS sensor, disconnection.
497008 On manual operation Alarm
Motor disconnection was detected
Disconnection to motor was detected.(Only stop mode)
Check the motor wiring.
497009 On manual operation Alarm
Error in Control Power Voltage
Control power for driver dropped. Check out the Power supply line.(24V Line)
49700a On manual operation Alarm
-----
Reserved Function of driver. Please make inquiries when error is detected.
49700b On manual operation Alarm
-----
Reserved Function of driver. Please make inquiries when error is detected.
49700c On manual operation Alarm
-----
Reserved Function of driver. Please make inquiries when error is detected.
49700d On manual operation Alarm
-----
Reserved Function of driver. Please make inquiries when error is detected.
49700e On manual operation Alarm
-----
Reserved Function of driver. Please make inquiries when error is detected.
1012-005
4OM-1603
3-94
3. Error IDs and Remedial Procedures : Chap.3
Error ID Error Name, Description, Cause, and Remedy
49700f On manual operation Alarm
System Error
System Error of internal driver. Driver error is supposed if this problem happens
frequently.
497101 Before setup P.C.B. detected
PCB was detected on Input conveyor.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497102 Before setup P.C.B. detected
PCB was detected on Positioning Conveyor(Input position)
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497103 Before setup P.C.B. detected
PCB was detected on Positioning Conveyor(Output position)
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497104 Before setup P.C.B. detected
PCB was detected on Output conveyor.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497105 Before setup P.C.B. detected
PCB was detected on Input conveyor of A Lane.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497106 Before setup P.C.B. detected
PCB was detected on Positioning Conveyor of A lane(Input position)
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497107 Before setup P.C.B. detected
PCB was detected on Positioning Conveyor of A lane(Output position)
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497108 Before setup P.C.B. detected
PCB was detected on Output conveyor of A Lane.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
1012-005
4OM-1603
3-95
3. Error IDs and Remedial Procedures : Chap.3
Error ID Error Name, Description, Cause, and Remedy
497109 Before setup P.C.B. detected
PCB was detected on Input conveyor of B Lane.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
49710a Before setup P.C.B. detected
PCB was detected on Positioning Conveyor of B Lane(Input position).
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
49710b Before setup P.C.B. detected
PCB was detected on Positioning Conveyor of B Lane(Output position).
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
49710c Before setup P.C.B. detected
PCB was detected on Output conveyor of B Lane.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
49710d Before setup P.C.B. detected
PCB is detected from Shuttle Conveyor in Input side.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
49710e Before setup P.C.B. detected
PCB is detected from Shuttle Conveyor in Output side.
Can not execute Conveyor width setup with the state of P.C.B. on Conveyor.
1. Remove P.C.B.
2. PleaseconrmthatP.C.B.
isexistinginMachine.
497201 Error in Support pin setup
Failed in recognizing Support Pin which will be pick-up.
Open the cover and set all support pins in Stock area. Then, Please edit Stock
area.
497202 Error in Support pin setup
Illegal support pin exists in the place where support pin will be set.
Open the cover and set all support pins in Stock area.Then, Please edit Stock
area.
497203 Error in Support pin setup
Failed in pick-up support pin
There is a possibility that Support pin is falling.
Open the cover and set all support pins in Stock area. Then, edit Stock area.
497204 Error in Support pin setup
Failed in detecting support pin after set it.
There is a possibility that Support pin is falling.
Open the cover and set all support pins in Stock area. Then, edit Stock area.
1012-005