4OM-1625-004_w.pdf - 第127页
4OM-1603 2-8 2. Management Information : Chap.2 Management Information Code Display Area A (The outline of the Management Information) Display Area B (The details of the Management Information) 01500F Nozzle Location Che…
4OM-1603
2-7
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
014b01 Nozzle Placement Data Check
Set the nozzle ID to use for the No.1 nozzle placement data.
015001 Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015002
Nozzle Location Check
"Notfoundttingnozzleforcalibration.(Front)
Set type "HA09A" nozzle on Head 2 Nozzle 1.
015003
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015004
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type ""HA09A"" nozzle on Head 2 Nozzle 1.
015005
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
015006
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
015007
Nozzle Location Check
Already set the different type nozzle.(Rear)
Remove it.
015008 Nozzle Location Check
Already set the different type nozzle.(Front)
Remove it.
015009 Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
01500A
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type ""FF01""or ""FF02"" nozzle on calibrate position.
01500B
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Rear)
Set type "VF02" nozzle on calibrate position.
01500C
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type "VF02" nozzle on calibrate position."
01500D
Nozzle Location Check
"Notfoundttingnozzleforcalibration.(Rear)
Set type "HA09A"or "Vf02" nozzle on calibrate position."
01500E
Nozzle Location Check
Notfoundttingnozzleforcalibration.(Front)
Set type "HA09A"or "Vf02" nozzle on calibrate position.
1012-005
4OM-1603
2-8
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
01500F Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015010 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015011 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015012 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015013 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Rear).Pleasesettype"BF02"nozzleinthe
stocker position where nozzle can change.
015014 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Front).Pleasesettype"BF02"nozzleinthe
stocker position where nozzle can change.
015015 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Rear).Pleasesettype"FA04"nozzleinthe
stocker position where nozzle can change.
015016 Nozzle Location Check
NotfoundttingnozzleforTeaching
(Front).Pleasesettype"FA04"nozzleinthe
stocker position where nozzle can change.
015101 Nozzle location teaching, check the position of nozzle on head
Could not found nozzle or Could not inspect nozzle (different type ?).
015102 Nozzle location teaching, check on the position of nozzle on head
Could not found or inspect nozzle (different type ?).
015201 Teaching check the conveyor
No P.C.B. on Conveyor. Please put P.C.B. in.
015202 Teaching check the conveyor
Please set P.C.B. positioning. Please set it again after cancel positioning if P.C.B.
positioning is already done.
015203 Teaching check the conveyor
-----
016001 Tray teaching
Traverse of Tray is not drawn out (Rear). Draw out Traverse.
016002 Tray teaching
Tray Traverse is not drawn out (Front). Draw out Traverse.
016101 Coplanarity Teaching
"Coplanarity Detection" of Test Operation Mode is set "No". Execute it after
cancelling Test Operation Mode.
016201 Coplanarity Test
Please pickup part.
1012-005
4OM-1603
2-9
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
017009 Teaching Check on the position of Glass jig
Necessary Glass Jig for Teaching does not exist. Please check that Glass Jig is
set in its position.
017201 Nozzle set-up(Rear)
Nozzle Pickup/Store mode of Stocker(Front) is not possible to operate. Please set
Stocker(Rear).
017202 Nozzle set-up(Rear)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017203 Nozzle set-up(Rear)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017204 Nozzle set-up(Rear)
Because of interference with Nozzle which is already placed, it cannot be placed.
Do not place Nozzle in the front and rear of two Odd nozzle placed.
017301 Nozzle set-up(Front)
Nozzle Pickup/Store mode of Stocker(Rear) is not possible. Please set
Stocker(Front).
017302 Nozzle set-up(Front)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017303 Nozzle set-up(Front)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017304 Nozzle set-up(Front)
Because of interference with Nozzle which is already placed, it cannot be placed.
Do not place Nozzle in the front and rear of two Odd nozzle placed.
017401 Button for inserting power
Can not supply power while Line Sensor program is on writing. Operate it after
writing completely.
017501 Operation
modesetconrmation
"Feeder Connection" or "Feeder Serial Communication" of Test Operation Mode is
set. Execute it after reset Operation Mode.
017601 Inching movement
Perform zeroing.
017602 Inching movement
Please push the Feeder Base Ready SW
017603
Inching movement
Close the safety cover of multi-tray, and press the Ready button).
017604 Inching movement
The range is out of movable Range.
017605 Inching movement
HL-axis is fallen. There is a possibility of collision between Noz and axis.
Please perform zeroing of HL-axis or move it to origin position.
1012-005