1OM-1626-001_w.pdf - 第121页

1OM-1610 3-2 1. Automatic Operation : Chap.3 091 1-001 1.1 Inspections before Automatic Operation 1.1.1 ConrmationofPowerSupply Conrm that the main breaker of the power supplied to the machine is turned "ON&qu…

100%1 / 227
1OM-1610
3-1
1. Automatic Operation : Chap.3
0911-001
1. Automatic Operation
Shown below is the ow of the automatic operation.
Refer to "Chapter 3" for details.
1.1.1 Power Supply
1.1.2 Confirmation of Air Pressure
1.1.3 Confirmation of Cover Section
1.1.4 Safety Confirmation of Machine Surroundings
1.2.1 Power ON
1.2.2 Preparation for Components
1.2.3 Preparation for PCBs
1.3.1 Starting the sysytem program
1.3.2 Login Operation
1.3.3 "AUTO OPN." Window
2. Component Replenishment
3. PCB Replenishment
4.1 Stop of Machine Operation
4.2 Interruption of Automatic Operation
1.4.1 Stop of Automatic Operation
1.4.2 Logout
Program Change Operation
Inspections before
Automatic Operation
Preparation before
Automatic Operation
Start of Automatic
Operation
Replenishment of
Components and PCBs
Stop, Interruption, and
Restart of Automatic
Operation
End of Automatic Operation
Flow of Automatic Operation F1C1
1OM-1610
3-2
1. Automatic Operation : Chap.3
0911-001
1.1 Inspections before Automatic Operation
1.1.1 ConrmationofPowerSupply
Conrm that the main breaker of the power supplied to the machine is turned
"ON".
• Power Supply : 200 ± 20 V AC, 3-Phase
• Apparent Power : Approx. 6.1 kVA
1.1.2 ConrmationofAirPressure
Conrm that the air pressure is set to the following.
•
Main Pressure : 0.45 MPa (4.6 kgf/cm
2
)
Note
The above represents the pressure specied while the machine is in
the"STOP" mode.
Min. 0.4 MPa (4.1 kgf/cm
2
) is required while the machine is running.
•
Air Blowing Pressure : 0.05 MPa (0.5 kgf/cm
2
)
Main Pressure
0.45 MPa (4.6 kgf/cm
2
)
Air Blowing Pressure
0.05 MPa (0.5 kgf/cm
2
)
F1C2
Notice
(a) Donotchangethesettingoftheairpressure.Otherwise,the
pneumaticdeviceswillnotworknormally.
(b) Besuretousedryandcleanair.Ifmoisture,oil,dust,etc.,enter
apneumaticdevice(aircylinder,etc.,usedinthismachine),itwill
resultinabreakdownofthemachine.
Note
DryandCleanAir:
Moisture : Dew Point -17°C or less (Atmospheric Pressure)
Oil : 0.1 mg/m or less (ANR)
Dust : Solid 0.01 mm or less
1OM-1610
3-3
1. Automatic Operation : Chap.3
0911-001
1.1.3 ConrmationofCoverSection
DANGER
There are strong motorized and high-voltage areas
inside the machine. Special caution should be paid
not to touch them.
Doing otherwise will cause personal injury (serious
accident).
•
Onlyqualiedmaintenancepersonnelshould
detach the covers.
•
The machine should be operated with the covers
being attached.
•
If a cover is detached, be sure to reattach it.
•
Be sure to close the transparent covers (door type)
before operating the machine.
•
Do not disengage the interlock mechanism of the
transparent covers (door type).
Conrm that the transparent covers above the beams, the safety covers around the
frame, the trans carent covers in the electrical parts storage sections (located under
both ends of and the conveyors) are closed.
Transparent Covers
(Door Type, located over the beams)
Transparent Covers
(Door Type, located over
the beams)
Safety Cover
(locatd around frame)
Safety Cover
(locatd around frame)
Front Side of Machine
Storage Cover of Electrical
Part Storage Box
(located on the lower area
of both conveyor ends)
Cover Lock Switch
(Stage Ready Switch)
F1C3