FLEXLINE-CAD_INM.pdf - 第27页
22 3.6 Delet ing (uninstalli ng) Flexl ine CAD Delete Flexline CAD according to the following procedure : 1. S elect the "Add and delete programs" command from "Control panel menu ”. 2. From the "Add …
21
7. The install completion screen is displayed. This completes the installation of the driver
for the protect module. Click the [Finish] button.
Figure 3.4.7-7 Completion of installation
3.5 Installing Flexline CAD Version 5.10 or earlier *1
If the old version of Flexline CAD program is already installed on your personal computer (PC),
install the new one by overwriting the old version. You can install the new version after
uninstalling the old one. See Section 3.2 “Deleting (uninstalling) old version Flexline CAD” for
how to uninstall Flexline CAD.
● Software to be installed is provided in the 3.5-inch floppy disk.
● If you use a 3.5-inch floppy disk
1. Start up Windows.
2. Quit all of the unnecessary programs.
3. Set the first disk into the corresponding drive.
4. Execute the setup program in either one of the following two ways:
a) Open the folder of the corresponding drive, and then select the icon for setup.
b) Click the <Start> button, and then the [Run…] command to select the icon for setup.
5. The program for setting up Flexline CAD is loaded, and then installation starts. Follow
the instructions on the dialog box displayed with the installation program to load Flexline
CAD. The instruction for entering the name of the directory in which Flexline CAD is to
be loaded is displayed on the screen. Although the default directory is
C:\Flexline\FlexCAD, you can change it to another one. If the specified directory does not
exist, a new directory is created automatically.
6. The instruction for inserting the next disk is displayed on the screen. Follow the
displayed instructions to set up the system.
7. On the last screen, the question for displaying the README file and the instruction for
restarting the computer may be displayed.
*1 Enabled with the Version 5.10 or earlier.
22
3.6 Deleting (uninstalling) Flexline CAD
Delete Flexline CAD according to the following procedure:
1. S
elect the "Add and delete programs" command from "Control panel menu”.
2. From the "Add and delete programs" screen, select the "Flexline CAD" icon and click t
he
"Delete" button.
3. A message to confirm the deletion of Flexline CAD is displayed. Then, click the "Yes
"
but
ton.
4. The progress of deletion is displayed. Flexline CAD is deleted.
3.7 Deleting (uninstalling) the driver for the protect module
Even if the Flexline CAD has been deleted (uninstalled), the driver for the protect module is not
deleted (uninstalled).
To update Flexline CAD into a new version, it is not necessary to delete the driver for the protect
module. However, when deleting the driver for the protect module, execute the following
procedures:
1. Select the "Add and delete programs" command of the "Control panel” menu.
2. From the "Add and delete programs" screen, select "Sentinel Protection Installer" ic
on and
c
lick the button.
3. A message to confirm the deletion of the driver is displayed. Then, click the "Yes" button.
4. The progress of deletion is displayed. The driver for protect module is deleted.
3.8 Troubleshooting
3.8.1 Flexline CAD does not start up when the protect module is connected to
the PC.
If the message “E4401200 The Flexline CAD protect module is not connected to the local PC.
Flexline CAD will exit.” appears on the screen although the protect module is connected to the
PC, and Flexline CAD does not start up, follow the procedure described below.
1. Disconnect the protect module from the PC.
2. Select “Add or Remove Programs” on the “Control Panel.”
3. Select “Sentinel Protection Installer” on the “Add/Remove Programs” screen, and then
click the “Delete” button.
4. Select “Device Manger” on the “Control Panel.”
5. Select “SafeNet USB SuperPro/UltraPro” from the “Universal Serial Bus controllers”
displayed on the “Device Manger” screen, and then click the “Delete” button.
6. Put a check mark to the “Delete the driver software for this device” option on the “Confirm
Device Removal” screen, and then click the “OK” button.
7. Open the “Downloaded Installations” folder of the “My Documents” folder with the
Explorer, and then search for a file with the “Sentinel Protection Installer.”
8. Delete a file(s) whose extension is “.msi” of the searched files.
9. Execute “setup.exe” of the “FlexlineCAD,” and then install the driver of the protect module
again.
10. Restart the Operating System (OS).
23
Chapter 4 Trying to Start Flexline CAD
4.1 Starting Flexline CAD
The following two methods are available:
• Turn on the power supply of the personal computer. Then, Windows is booted up.
(1) Double-click the Flexline CAD icon provided on the desktop.
Double-click
Figure 4.1-1 Desktop icon of Flexline CAD
(2) From the ”Start" menu, select the "Programs" - "JUKI" - "Flexline CAD" - "Flexline CAD"
command. *1
Figure 4.1-2
*1 Enabled with the Version 6.00 or later only. (Some functions may be enabled with the latest
version only.)