FLEXLINE-CAD_INM.pdf - 第64页
59 7.6 Field translati on screen In each dat a item, the represent ation of CAD data must be matched to the sett ings in Flexline CAD. For example, when the placement side is defined, the top side and the bott om side ar…
58
7.5.5 Definition of IC mark 3 in the placement section
The formats applicable to IC mark 3 are as follows: Even if data conversion is performed with
the other format as an output format, IC mark 3 is not output. The IC mark 3 field is not
displayed in the data change dialog box.
• HLC Ver 6.0 to 12.0
• IS 2.00
• IS,IS Lite
• 2050 Ver 1.XX
• 2050R Ver 1.XX
• 2055R Ver 1.XX
• 2060 Ver 1.XX
• 2070 Ver 1.00/1.XX/2.1X
• 2060R Ver 1.XX
• 2080 Ver 1.00/1.XX/2.1X
• 2080R Ver 2.1X
• 3020 Ver 1.00
• 3020R Ver 1.00
• 3010 Ver 1.00
• 3020V Ver 1.00
• 3020VR Ver 1.00
• 3010A Ver 1.00
• 3020VA Ver 1.00
• 3020VRA Ver 1.00
• FX-1 Ver 1.XX
• FX-1R Ver 1.XX
• FX-2 Ver 1.00/1.XX
• FX-3 Ver 1.00/1.XX/3.50
• FX-3R Ver 4.XX
• FX-3RA Ver 1.00
• CX-1 Ver 1.00/1.XX
• RX-6 Ver1.00
• RX-6R Ver4.00
• RS-1 Vre1.00
• LC-01
NOTE:
Select the "IS, IS Lite" when you want to output in JaNets format.
59
7.6 Field translation screen
In each data item, the representation of CAD data must be matched to the settings in Flexline
CAD.
For example, when the placement side is defined, the top side and the bottom side are defined
as "T" and "B" respectively in the CAD data. However, because Flexline CAD does not know
whether the top side is "T" or "B", it is necessary to define that the top side is "T."
Figure 7.6-1 Field Translation defining method
* Regarding the field requiring field
translation, refer to "10.3 Field."
2. Select production program keyword.
1. Select the line (line of a yellow background) of the
field that requires field translation. Then, the
"data transformation settings" screen of the lower
column is displayed.
3. Enter the corresponding CAD data keyword.
60
7.6.1 Definition of valid/invalid data
To convert only line 3 to line 5 ignoring line 1 and line 2 when the following data exists, set the
lines containing "F" to Invalid (or lines containing "D" to Valid).
(1 1 "F" 1 -30908 307 0 0 0 0 0 "R1" "" "" "" "" 0 0 0 2 0 0 0 0 0 0 0 "" )
( 2 1 "F" 1 -3231 27734 0 0 0 0 0 "R1" "" "" "" "" 0 0 0 1 0 0 0 0 0 0 0 "" )
( 3 1 "D" 1 -30274 5385 5400 1 2 0 0 "F222" "" "" "" "" 0 0 0 0 0 0 0 0 0 0 0 "" )
( 4 1 "D" 2 -30783 3863 5400 1 2 0 0 "F05" "" "" "" "" 0 0 0 0 0 0 0 0 0 0 0 "" )
( 5 1 "D" 1 -29384 3352 5400 1 2 0 0 "F345" "" "" "" "" 0 0 0 0 0 0 0 0 0 0 0 "" )
Figure 7.6.1-1 Field translation (Invalid Data setting)
Figure 7.6.1-2 Field Translation (Valid Data setting)
1. Select the line to set field.
3. Enter "F" in CAD Data Keyword.
2. Select "Invalid Data" in Production Program Keyword.
* When "Invalid Data" is defined,
not only "Invalid Data" fields
but also the whole line are not
converted.
1. Select the line to set field.
translation.
* In each section, up to 10
"Valid Data" and "Invalid
Data" can be defined.
3. Enter "D" in CAD Data Keyword.
2. Select "Valid data" in Production Program Keyword.