YST15_Users_E.pdf - 第168页

3-18 3 Y early maintenance items 3.5 Checking the tension of Y -axis drive belt n NOTE Use a step ladder as required for the maintnance item which are located in high place. 1 T urn the machine off. 2 Mo ve the handler d…

100%1 / 182
3-17
3
Yearly maintenance items
3.4 Checking the white belt of Y-axis
1
Turn the machine off.
2
Move the handler on Y-axis to the
place where it is easy to work.
Open a side door, then move the handler a
little upper from the middle on Y-axis so that
it is easy to work.
3
Check the block fixing Y-axis belt.
1. Use a hex wrench (3 mm) to check if the
nut, which fixes the slider, for the block
fixing Y-axis belt is tighten securely.
2. Check if the block fixing Y-axis belt
doesn't interfere with the rail.
3. Check if the bolt fixing Y-axis belt is
tighten securely.
4
Check if Y-axis belt is fixed
securely.
1. Move the handler to the place where it is
easy to see Y-axis weight on Y-axis by
hands.
2. Use a hex wrench (4 mm) to check if the
bolts fixing Y-axis belt are tighten secure-
ly.
5
Check Y-axis belt.
Move the handler up and down on Y-axis by
hands to check if there are contamination
or damage on the belt.
6
Check Y-axis belt on the other side.
Repeat Step2 to Step5 to check Y-axis belt
on the other side.
Y-axis weight
Step 4
Check if the fixing bolts are tighten securely.
Y-axis weight
53323-KMS-00
The block fixing Y-axis belt
Step 3
Check if the nut is tighten
securely
The block fixing
Y-axis belt
The bolt fixing Y-axis belt
is tighten securely.
Check if the block doesn't
interfere with the rail.
53322-KMS-00
3-18
3
Yearly maintenance items
3.5 Checking the tension of Y-axis drive belt
n
NOTE
Use a step ladder as required for the maintnance item which are located in high place.
1
Turn the machine off.
2
Move the handler down most on
Y-axis.
Open a side door, then move the handler
down most on Y-axis.
3
Check the tension of Y-axis drive
belt.
Y-axis motor and its drive belt are located in
up left viewed from the machine front.
The belt tension able to be rotated just 90
degree with fingers pinching is appropriate.
If the belt doesn't rotate easily or it rotates
too much, adjust the belt tension by the
following procedure.
4
Move the handler to Initialization
standby position.
Move the handler to Initialization standby
position by hands.
Check the tension of Y-axis drive belt
Step 3
Y-axis drive belt
53324-KMS-00
3-19
3
Yearly maintenance items
Adjust the tension of Y-axis drive belt
n
If the tension is low (the belt rotates too much)
1
Loosen four bolts A in the figure
Use a wrench (10 mm) to loosen four bolts A
shown in figure.
2
Tighten two bolts B a little.
Use a hex wrench (5 mm) to tighten two
bolts B a little shown in figure.
n
NOTE
Tighten two bolts B with same amount. Do not tighten
only one bolt biasedly.
3
Check the belt tension.
Follow Step3 in "3.5 Checking the tension of
Y-axis drive belt" to check the belt tension.
4
Tighten the bolts A.
After confirming the tension is appropriate,
tighten the bolts A.
n
If the tension is high (the belt doesn't rotate easily)
1
Loosen four bolts A in the figure
Use a wrench (10 mm) to loosen four bolts A
shown in figure.
2
Loosen two bolts B a little.
Use a hex wrench (5 mm) to loosen two bolts
B a little shown in figure.
n
NOTE
Loosen two bolts B with same amount. Do not loosen
only one bolt biasedly.
3
Check the belt tension.
Follow Step3 in "3.5 Checking the tension of
Y-axis drive belt" to check the belt tension.
4
Tighten the bolts A.
After confirming the tension is appropriate,
tighten the bolts A.
Adjust the tension of Y-axis drive belt
A B
Step 1,2
53325-KMS-00
Adjust the tension of Y-axis drive belt
A B
Step 1,2
53325-KMS-00