00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第166页
7 Conveyor 7.2 Loosening the Conveyor Side Clamps 166 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 Version 3 Fig.217: Clamp ► Loosen the conveyor side clamps. To do this, press the lever (1) upwards and push …
7 Conveyor
7.2 Loosening the Conveyor Side Clamps
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 165
7.2.2 Moving the Conveyor Sides by Manually Releasing the Side Clamps
Parts, equipment and tools
●
Per side:
3x ISO4762-M3x16-A2-70 [03042545-xx]
Procedure
► Move the conveyor sides to a position which gives you good access to the clamps.
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
NOTICE
Marking the starting positions
After completing this task, it is helpful to move the conveyor sides back to their approximate
starting positions.
► You may want to mark the current positions of the conveyor sides.
Do not mark the clamping surface or the guide rails.
CAUTION
Loosen all clamps
You always need to loosen all clamps for one conveyor side.
Version 1
Fig.215: Clamp
► Loosen the conveyor side clamps.
To do this, press the clamp(1)
(e.g.
with a screwdriver) upwards and turn or
insert a screw (M3x16) into the
hole(2)
.
CAUTION!
Make sure that you do not distort the
guide plate(3)
. If you do, this could
lead to problems with recognizing the
position of the conveyor side.
.
Version 2
Fig.216: Clamp
► Loosen the clamps on the conveyor
sides.
To do this, remove the disks above the
clamp compression springs (2 screws
for each disk). To do this, undo both
screws (1)
on the clamps (2x for each
conveyor side).
CAUTION!
Compression springs
The compression springs are tensioned.
Make sure that you do not lose these.
.
7 Conveyor
7.2 Loosening the Conveyor Side Clamps
166 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
Version 3
Fig.217: Clamp
► Loosen the conveyor side clamps.
To do this, press the lever(1)
upwards
and push a suitable pin or a screw into
the hole(2)
.
► Repeat these steps for all clamps on the sides concerned.
CAUTION
Always loosen all clamps for one conveyor side!
► Always loosen all clamps for one conveyor side.
ð SIPLACE X-Series S machines have three clamps fitted per conveyor side.
► If you do not loosen all clamps for the conveyor side, this could be easily damaged.
You can now move the sides.
CAUTION
Moving the sides
► When the clamp is manually loosened, make sure that you only move the conveyor
sides by pushing against the clamping units.
► Make sure that you always move the conveyor sides parallel.
► Take care not to distort or trap the conveyor sides when pushing!
Restoring the clamp
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► After completing the work, push the conveyor sides back into their approximate starting posi-
tion.
► Make sure that the conveyor sides are back in their original positions after switching on.
► Perform a reference run.
► Perform side calibration for the fixed side on the left and right. If you do not, not all conveyor
sides will be calibrated.
This calibration is needed to ensure that the conveyor sides are positioned correctly.
► Calibrate the PCB sensors.
► Use a board to test the parallelism. This board must be transported evenly through the entire
conveyor.
7.10.2 "Setting the Parallelism of the Conveyor Sides and Adjustment Units" [}248]
► Re-establish the original conveyor configurations:
For more information, go to Service menu and select Conveyor configuration - Set options
for conveyor fixed rail.
Then select one of the positions and click on the Adjust configuration button
.
Then reset the conveyor sides to the previous configuration.
7 Conveyor
7.3 Lifting Table
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 167
7.3 Lifting Table
DANGER
Press the EMERGENCY STOP!
Before performing adjustment work you must ensure that the lifting table has been secured
against movement!
7.3.1 Replacing the lifting table plate
Parts, equipment and tools
●
Single conveyor SIPLACE X-Series S:
Lifting table assembly 701 mm [03088801-xx]
●
Dual conveyor SIPLACE X-Series S:
Lifting table plate 1 assembly 350 mm [03088811-xx]
Lifting table plate 2 assembly 350 mm [03093910-xx]
Overview
Fig.218: Lifting table plate (example of single conveyor
used)
1. Lifting table plate
2. Fastening screws for lifting table plate
Removal
NOTICE
Single, dual conveyor
The replacement is shown in the diagram using the example of a lifting table unit for the
dual conveyor (DC). Replacement on a single conveyor (SC) follows the same procedure.
NOTICE
Does the lifting table stay in the top position?
If the lifting table remains in the top position and cannot be lowered, you will not be able to
dismantle the lifting table plate. In this case, call the SIPLACE Service team.
NOTICE
Lifting table plate guides
► Make sure that the lifting table guides are not mixed up. If you do, you will need to re-
set the parallelism of the lifting table plates.
► Use the software to move the conveyor sides into a position which allows you best access. As
an alternative, you can loosen the clamps for the relevant sides in dual conveyors.
7.2 "Loosening the Conveyor Side Clamps" [}162]