00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第266页
8 Head exchange 8.6 Replacing the SIPLACE C&P20P2 266 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 For additional work to the placement head: 03056231‑xx Head mount For vacuum pump operation: 00198599‑xx V…
8 Head exchange
8.6 Replacing the SIPLACE C&P20P2
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 265
8.6 Replacing the SIPLACE C&P20P2
NOTICE
Retrofitting the SIPLACE C&P20 P2
The SIPLACE C&P20P2 can be retrofitted from machine numbers H1440.
The following prerequisites must be fulfilled:
► The head interface [03091013‑xx] / [03091023‑xx] must have at least FS04.
► The gantry sensor [03071974‑xx] must have at least FS02.
► The MGCU-3 [03103477-xx] must have at least FS04.
► The MGCU-2 [03117531‑xx] must have at least FS03.
► An X-FCU with 80 MHz [03170613-xx] must be fitted.
Parts
Fig.351: SIPLACE C&P20P2 with camera
03147200-xx SIPLACE C&P20P2 placement head with camera
03126608-xx SIPLACE C&P20P2 placement head without camera
NOTICE
Vacuum pump/compressed air operation
As a spare part, the head is prepared for vacuum pump operation and is fitted with the
"Aperture ring assembly C&P20 P" [03116883‑xx].
► The SIPLACE C&P20P2 must be converted with the conversion kit "Compressed air
C&P20x" [03106765‑xx] or with the "Holding circuit assembly C&P20" [03005123Sxx]
for operation in compressed air mode.
Equipment and tools
03078400‑xx Torque screwdriver ESD 1.0-5.0 Nm
03078706‑xx Bitholder for screwdriver TorqueVario
03073256‑xx Extension/ straight TX20
03156306-xx Component sensor protective cap
03157023‑xx Calibration piece SST48/49
03034148-xx Calibration part version SST23
03162648-xx Packaging SIPLACE C&P20 P2 assembly (transport box)
00198607-xx Service manual "SIPLACE C&P20P2 head"
00353832-xx Allen key set
Wire cutters
Cable tie
8 Head exchange
8.6 Replacing the SIPLACE C&P20P2
266 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
For additional work to the placement head:
03056231‑xx Head mount
For vacuum pump operation:
00198599‑xx Vacuum pump operation: assembly instructions "Vacuum pump SIPLACE X-
Series S option from Hxxxx"
Hoses, if required:
03006727‑xx Silicone hose Di 8 Da 12 conductive (for exhaust air hose C&P20P2 295mm
[03138202‑xx])
03178204‑xx 83mm
03055411-xx Plastic hose PUN-CM-6-SW anti-static (for hose to machine for C&P20P2
[03154803‑xx])
00359177‑xx Hose 4*2.5 PUN-CM-4 (for return cylinder hose C&P20P2 135mm
[03154509‑xx])
Removal
NOTICE
Vacuum test
► If required, perform a vacuum test before removing the placement head.
Read the "Service manual Vacuum test at C&P placement head" [DE+EN:
00196101‑xx] for this.
NOTICE
Fast Hardware Exchange (FHE)
► Observe the instructions in section 8.1 "Fast Hardware Exchange" [}253] when ex-
changing a head.
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
Fig.352: Component sensor protective cap
CAUTION!
Component sensor!
The component sensor prisms, under-
neath the placement head, are highly
sensitive.
Never place the placement head down
on the component sensor.
.
► Fit the protective cap onto the compo-
nent sensor for the placement head.
8 Head exchange
8.6 Replacing the SIPLACE C&P20P2
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 267
Fig.353: Electrical connections
► Open the cable ties and unplug the
electrical connections(1)
from the Vis-
ion Head Interface.
Open the cable ties, if needed(2)
.
► Pull the plastic cover(3) over the inter-
mediate distributor and off (press
studs).
► Disconnect the two flat ribbon
cables(4)
from the intermediate distrib-
utor.
Fig.354: Pulling off the hoses
► Pull the hose(1) off.
► Pull the hose(2) off the holding circuit
connection.
Fig.355: Exhaust air hose
► Pull the exhaust air hose on the filter
off.