00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第186页
7 Conveyor 7.5 Width Adjustment, Clamps and Cylinder Unit 186 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 Fig.240: Connections (example of SIPLACE SX1/SX2 shown) ► Disconnect the cylinder unit from the electr…
7 Conveyor
7.5 Width Adjustment, Clamps and Cylinder Unit
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 185
7.5.5 Replacing the cylinder unit (width adjustment) (DC only)
Parts, equipment and tools
●
Cylinder unit 1 SX4a [03087394-xx] (output area)
●
Cylinder unit 2 SX4a [03087398-xx] (input and intermediate conveyor area)
Overview
Fig.238: Overview cylinder unit
1. Cylinder unit
2. Trailing cable
3. Cover plate (the trailing cable is
fastened to it - not part of the delivery
package)
4. Pneumatic connections
5. Electrical connections
See also 7.5.1 "Overview of width adjustment" [}181]
Removal
NOTICE
Location 3 or 4
We recommend that, if possible, this task is performed from location 3 or 4.
► Use the software to move the conveyor sides into a position which allows you best access. As
an alternative, you can loosen the clamps for the relevant sides in dual conveyors.
7.2 "Loosening the Conveyor Side Clamps" [}162]
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}86]
► You can also dismantle the lifting table plate for better access.
Fig.239: Cylinder unit (example of SIPLACE SX1/SX2 shown)
NOTICE!
The cover plates (1) and (2) can only
be dismantled if the cylinder unit is not
above it. You may need to gently pull
on the width adjustment belt to move
the cylinder unit.
.
► Remove the screws fastening the cover
plate (1)
.
► Remove the screws fastening the cover
plate (2)
.
► Remove the two screws fastening the
cylinder unit (3)
. You can now lift the
cylinder unit up and off.
CAUTION!
The cylinder unit is pinned and can be
stiff to move.
.
7 Conveyor
7.5 Width Adjustment, Clamps and Cylinder Unit
186 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
Fig.240: Connections (example of SIPLACE SX1/SX2
shown)
► Disconnect the cylinder unit from the
electrical(1)
and pneumatic(2) sup-
plies. These are located under the
cover plates or in the intermediate con-
veyor, at the conveyor control.
You may want to mark their positions,
to make clear assignment easier later
on.
► Take the cylinder unit out of the machine, together with the cover plate.
► Remove the screws fastening the trailing cable to the cover plate.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► Make sure that the cable is run correctly and does not rub against any parts.
Fig.241: Fitting the cylinder unit
1. Trolley
2. Cylinder unit
3. The cylinder unit must lie flush against
the carriage. Make sure that there is no
gap in-between.
► Make sure that the cylinder unit (2)lies
flush against the trolley (1)
when you
screw it into place.
► Replace any open cable ties.
Make sure that the cable ties and the heads of the cable ties do not rub against any parts
when you do this.
► After installation, make sure that the cylinder piston does not protrude above the other parts.
You might need to place washers between the adapter plate and the cylinder.
► After installation, check whether the cylinder unit can be moved along the entire width of the
conveyor. Make sure that there are no interfering edges etc.
► Check the distance to the clamping units.
7.5.10
"Information About the Clamping Unit Versions (DC Only)" [}191]
► Recalibrate all conveyor sides for lane1 and2 (both in Dual conveyor right mode and in
Dual conveyor left mode
).
7 Conveyor
7.5 Width Adjustment, Clamps and Cylinder Unit
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 187
7.5.6 Replacing the proximity switch for the cylinder unit (width adjustment) (DC only)
Parts, equipment and tools
●
New: proximity switch SME-8M-DS-24V-K-2.5 [03100139-xx]
or
Old: proximity switch SME-8-K-LED-24 [00343651-xx]
Overview
Fig.242: Sensor system (example of SX1/SX2 shown)
1. Proximity switch for the cylinder
2. Grub screw for fastening the sensor
3. Inductive sensor (position detection for
conveyor side)
See also 7.5.1 "Overview of width adjustment" [}181]
Removal
► Remove the cylinder unit. Please read section 7.5.5 "Replacing the cylinder unit (width adjust-
ment) (DC only)" [}185].
► Remove the screw fastening the proximity switch.
► Loosen the screw fastening the sensor.
► Open the trailing cable and remove the sensor cable.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► Dismantle the connector from the old proximity switch and fit it in the new proximity switch. To
do this, release the crimp connections on the old proximity switch from the connector and in-
sert them into the new proximity switch. Note the correct assignment for this!
► Fix the new proximity switch to the correct position (see below).
► The sensor must lie flush against the surface of the cylinder unit.
Fig.243: Setting the proximity switch
1. Distance between the lower edge of the
head plate and the upper edge of the
proximity switch:
●
13 mm for new proximity switch
SME-8M-DS-24V-K-2.5 [03100139-xx]
●
10 mm for old proximity switch SME-8-
K-LED-24 [00343651-xx]