00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第274页

8 Head exchange 8.8 Replacing the SIPLACE Twin 274 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 Conversion to another installation height Fig.368: Conversion 1. Hole for the fastening screw of the bushing in &…

8 Head exchange

8.7 Replacing the SIPLACE CPP/M

Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 273

8.7.1 Preparing the SIPLACE CPP for the installation height

CAUTION

Different heights

The placement head can be installed at two different heights.

Installation position low: CPP_L corresponds to a component height of six mm maximum.

Installation position high: CPP_H corresponds to a component height of 11.5 mm max-

imum.

► If the SIPLACE CPP is used in a placement area with stationary camera, SIPLACE

Twin or SIPLACE WPC, it may only be used in the upper position!

► If the SIPLACE CPP is operated in mixed mode with a SIPLACE C&P20P2, this will

need to be fitted in the bottom position!

Overview

Fig.366: Fastening screws

1. Fastening screws on the left side

2. Fastening screws on the right side

This diagram shows the fastening screws in

the "head at top" position.

Fig.367: SIPLACE CPP – positions

1. Retaining plate

2. "Head at bottom" position

3. "Head at top" position

4. Fixture holes with bushings for the cap-

tive screws

8 Head exchange

8.8 Replacing the SIPLACE Twin

274 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021

Conversion to another installation height

Fig.368: Conversion

1. Hole for the fastening screw of the

bushing in "head at bottom" position

2. Hole for the fastening screw of the

bushing in "head at top" position

3. Bushing

All four bushings and the retaining plate

must either be fixed in top or bottom posi-

tion.

Proceed as follows when replacing the

bushings:

► Undo the fastening screws of the bush-

ings.

► Insert the bushings in the correct posi-

tion and re-tighten them.

► Perform these steps for all four fasten-

ing bushings and the retaining plate for

the head.

8.8 Replacing the SIPLACE Twin

Parts, equipment and tools

●

Select the relevant placement head:

– Twin Pick&Place module [03033628-xx]

– Twin Pick&Place module THK R2 [03097485-xx]

●

Torque screwdriver 1-5 Nm [03078400-xx]

●

Extension/straight TX20 [03073256-xx]

●

Extension/straight [03043440-xx]

●

Bit holder for Torque Vario-S screwdriver [03078706-xx]

●

Calibration tool version 3 [03010565-xx]

For additional work to the placement head:

●

Head mount [03056231‑xx]

●

Service manual "SIPLACE Twin" [DE:00197468‑xx] [EN:00197469‑xx]

●

Job Card "Preventive Maintenance Twin" [DE:00197604‑xx] [EN:00197603‑xx] (other lan-

guages available)

8 Head exchange

8.8 Replacing the SIPLACE Twin

Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 275

Overview

The Twin consists of two identical Twin modules (segments), which are fitted at an angle of 180°.

NOTICE

Module 1 and 2

The removal procedure is described here for module1 (left). Removal for module 2 (right)

is the same.

► In the case of older Twin modules, you might need to remove module 2 before remov-

ing module 1. During installation, you would then need to fit module 1 before fitting

module 2.

► In the case of newer Twin modules, the modules can be removed and fitted individu-

ally.

Fig.369: Captive screws

 NOTICE!

When using modules with captive

screws(1)

you may need to fit these

screws on the other side

depending on

the installation position.

.

Observe the various different hose lengths:

Designation Item no. Length

Other hoses on the machine:

Hose supplied "silicone hose. Di8 Da12 electrically conduct-

ive 1m"

03006727Sxx

●

Cooling air hose X motor 03006777-xx 180 mm

●

Cooling air hose P+P module right 03006779-xx 395 mm

●

Cooling air hose P+P module left 03006780-xx 230 mm

●

Cooling air hose X motor TX 03126503-xx 210 mm

●

Cooling air hose X motor rotated gantry 03059420-xx 440 mm