00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第248页
7 Conveyor 7.10 Conveyor sides 248 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 7.10.2 Setting the Parallelism of the Conveyor Sides and Adjustment Units 7.10.2.1 Setting the parallelism of the sides on the sin…
7 Conveyor
7.10 Conveyor sides
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 247
► Move the conveyor side into the required position.
► Insert the screws loosely. Press the side so that it engages with the screw holes either in a
forwards or backwards inclination (against all three holders in the same direction). Tighten the
fastening screws in the new position.
Fig.326: Setting the conveyor side
► In the software set the fixed conveyor
side and the position.
NOTICE!
This menu is accessible from operator
level Service (customer)!
.
7.10.1.2 Setting the Fixed Conveyor Side on Dual Conveyors
The fixed conveyor edge is always set with the software for dual conveyors.
Setting
Fig.327: Setting the conveyor side position
► In the software set the fixed conveyor
side and the position.
Conveyor Sides - Settings
NOTICE!
This menu is accessible from operator
level Service (customer)!
.
7 Conveyor
7.10 Conveyor sides
248 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
7.10.2 Setting the Parallelism of the Conveyor Sides and Adjustment Units
7.10.2.1 Setting the parallelism of the sides on the single conveyor
Overview
Fig.328: Overview of width adjustment
A Conveyor side A (fixed) B Conveyor side B (moveable)
1 Toothed belt (width adjustment) 2 Width adjustment (flange and spindle)
Setting
► This setting is identical for the dual conveyor. For more information about this, read section
7.10.2.2
"Setting the parallelism of the conveyor side walls and adjustment units for dual con-
veyors" [}249].
NOTICE
Procedure identical to that for adjustment units on dual conveyor
In a single conveyor, the movable conveyor side is directly connected with the recirculating
ball screws of the width adjustment. This is set via the toothed belt. This must jump one or
more teeth via the relevant idler pulleys.
7 Conveyor
7.10 Conveyor sides
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 249
7.10.2.2 Setting the parallelism of the conveyor side walls and adjustment units for dual
conveyors
NOTICE
Adjustment units
The parallelism of the conveyor sides depends on the parallelism of the adjustment units.
This is set via the toothed belt. This must jump one or more teeth via the relevant idler pul-
leys.
► If you unable to set the parallelism, contact your local SIPLACE Service team.
Parts, equipment and tools
Fig.329: Metal pieces
●
To check the adjustment unit stoppers,
you need two suitably sized and
identical pieces of metal (see below).
You could also use two lifting table
plate guides if needed.
Overview
Fig.330: Overview width adjustment
1. Adjustment units
2. Width adjustment drive
3. Movable idler pulley
4. Toothed belt of width adjustment
5. Measurement point for belt tension
6. Idler pulley
Setting
► Use the software to move the conveyor sides into a position which allows you best access. As
an alternative, you can loosen the clamps for the relevant sides in dual conveyors.
7.2 "Loosening the Conveyor Side Clamps" [}162]
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Dismantle the lifting table plate at location 3 and 4.
7.3.1 "Replacing the lifting table plate" [}167]
► Loosen the movable idler pulley for the toothed belt (width adjustment). The toothed belt of
the width adjustment should then have enough play so that you can move the adjustment
units independently of one another. You may need to remove the toothed belt from the idler
pulleys.