00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第270页
8 Head exchange 8.7 Replacing the SIPLACE CPP/M 270 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 8.7 Replacing the SIPLACE CPP/M Parts, equipment and tools Fig.360: SIPLACE CPP with camera ● SIPLACE CPP with c…
8 Head exchange
8.6 Replacing the SIPLACE C&P20P2
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 269
Fig.359: Fastening screws
► Tighten the four screws fastening the
head(1)
(M4, torque 2.7Nm).
CAUTION!
Do not distort
The screw must be turned 3-4 times
before the torque is reached.
If the torque is reached after only one
rotation, this probably means that the
screw has been inserted at a tilt.
.
NOTICE
Various hose lengths on SIPLACE X-Series S
The hose to the pressure control valve will vary in length, depending on the installation loc-
ation (standard gantry or rotated gantry).
► Shorten or replace the hose, where necessary.
Follow the removal instructions in reverse order for further installation.
See also
2 8.9 "Installation Positions on the Head Plate" [}278]
8 Head exchange
8.7 Replacing the SIPLACE CPP/M
270 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
8.7 Replacing the SIPLACE CPP/M
Parts, equipment and tools
Fig.360: SIPLACE CPP with camera
●
SIPLACE CPP with camera SST29 [03070108-xx] or
SIPLACE CPP without camera [03053528Sxx]
●
SIPLACE CPP [03053528Sxx] (without camera)
●
SIPLACE CPP M [03153719Sxx] (without camera)
●
Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
●
Extension/straight TX20 [03073256-xx]
●
Bit holder for TorqueVario screwdriver [03078706-xx]
●
Component sensor protective cap [03080984-xx]
●
Torx offset screwdriver TX8 [03080081-xx]
●
Calibration tool version 3 [03010565-xx]
●
Calibration tool version SST23 [03034148-xx]
●
Optional: upgrade kit for a cover over the intermediate distributor 2
Read also the technical information "Retrofit kit usability cover CPP" [DE:TI2018‑06D05]
[EN:TI2018‑06E05].
For additional work to the placement head:
●
Head mount [03056231‑xx]
●
Service manual "SIPLACE CPP" [DE:00197462‑xx] [EN:00197463‑xx]
●
Job Card "Preventive Maintenance CPP" [DE:00197505‑xx] [EN:00197503‑xx] (other lan-
guages available)
Overview
Fig.361: Overview (example of SIPLACE CPP head shown)
1. Fixture holes (two each, depends on in-
stallation height)
NOTICE!
The length of the exhaust air hose "Sil-
icon hose Di8 Da12 electrically con-
ductive 1m" [03006727Sxx] on the
SIPLACE CPP/CPP M is 316mm.
.
8 Head exchange
8.7 Replacing the SIPLACE CPP/M
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 271
Removal
NOTICE
Vacuum test
► If required, perform a vacuum test before removing the placement head.
Read the "Service manual Vacuum test at C&P placement head" [DE+EN:
00196101‑xx] for this.
NOTICE
Fast Hardware Exchange (FHE)
► Observe the instructions in section 8.1 "Fast Hardware Exchange" [}253] when ex-
changing a head.
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}86]
CAUTION
Take great care when dismantling the placement head!
The component sensor prisms, underneath the placement head, could be damaged.
► Never place the placement head down on the component sensor.
Fig.362: Component sensor protective cap
► Fit the protective cap onto the compo-
nent sensor for the placement head.
Fig.363: Connections
► Unplug the pneumatic connections(1)
from the placement head. You may like
to mark their positions, to make clear
assignment easier later on.
► Disconnect the flat ribbon cables(3)
from the intermediate distributor(2).