00198829-01_SM_X-Series-S_Hxxxx_EN.pdf - 第77页
4 Electrics and control system 4.7 Replacing the button Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 77 4.7 Replacing the button Parts, equipment and tools Fig.87: Overview of button 1. Pushbutton 2. Emergency…
4 Electrics and control system
4.6 Replacing the monitor/monitor holder
76 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
4.6 Replacing the monitor/monitor holder
Parts, equipment and tools
●
Monitor 12.1" without keyboard:
– Multitouch kit [03211595‑xx]
Contains:
Monitor DV1225-007 12.1 inch multitouch [03156514‑xx]
Adapter cable monitor 4 pin to 3 pin [03219712‑xx]
●
Monitor 15" with keyboard:
– Monitor SCD1520-TDC [03078913-xx]
– Keyboard kit [03211592‑xx]
Contains:
Keyboard rest center section assembly [03025743‑xx]
USB keyboard "Active Key" with touchpad [03059594‑xx]
●
Monitor holder [03042042‑xx]
●
Standard tooling
●
Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
●
Bit holder for TorqueVario screwdriver [03078706-xx]
Overview
Fig.86: Overview of monitor
1. Monitor
2. Screws fastening the monitor holder to
the machine
3. Monitor connections
4. Screws fastening the monitor to its
holder
5. Fulcrum screws
(torque 4.5Nm)
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Unplug all connections to the monitor. You may want to mark their positions, to make clear as-
signment easier later on.
► Loosen the upper and lower screws fastening the monitor bracket to the machine and lift the
monitor and its bracket out of the keyholes.
► Remove the four screws fastening the monitor to its bracket and then remove the monitor
bracket.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following note:
► Tighten the two fulcrum screws (left and right) with a torque of 4.5Nm.
4 Electrics and control system
4.7 Replacing the button
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 77
4.7 Replacing the button
Parts, equipment and tools
Fig.87: Overview of button
1. Pushbutton
2. Emergency stop button
3. Twin pushbutton
Square shape Round shape
Pushbutton 00334095‑xx 03164001Sxx
Emergency stop button 00334073‑xx 03165966Sxx
Twin pushbutton 03084513‑xx 03170336Sxx
Holder (for back of button
with round design)
--- 03164008‑xx
NOTICE
Square and round designs are not compatible with one another
The two designs are not compatible with one another and can not be exchanged with one
another.
► Always replace a button with one of the same design.
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the relevant button. To do this, unplug all electrical connections. You may like to
mark their positions, to make clear assignment easier later on.
Installation
Follow the removal instructions in reverse order for installation.
4 Electrics and control system
4.8 Replacing the CAN interface CINX
78 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
4.8 Replacing the CAN interface CINX
Parts, equipment and tools
Fig.88: CAN interface CINX
1. CAN interface CINX [03108598-xx]
2. DIP switches
Overview
Fig.89: CAN interface in the machine
The CAN interface(1) is located between
location 1 and 2, behind the BoxPC(2)
.
The CAN interface is fixed with Velcro to the
machine base.
The CAN interface also features four con-
nections for diagnostics.
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Lift off the keyboard (if present).
► Dismantle the lower cover between locations 1 and 2.
► Lift the BoxPC slightly and swing it forwards.
► Unplug all electrical connections to the CAN interface. Mark their positions, to make clear as-
signment easier later on.
► Take the CAN interface out of the machine.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following note:
► Set the DIP switches. (see below).
DIP switch
Machine type DIP switch left DIP switch right
1 2 1 2
X-Series S ON ON ON ON
SX1/SX2 OFF OFF OFF OFF