LCX_UserManual_en_08_1.pdf - 第70页

Instrument functions R&S ® LCX Series 70 User Manual 1 179.2260.02 ─ 08 8 Instrument functions This section includes the basic instrument functions and operating modes. Y ou can configure these functions, either dire…

Performing measurements

R&S

LCX Series

69User Manual 1179.2260.02 ─ 08

short

secondaryprimary

Figure 7-2: Leakage inductance measurement

The inductance value of the primary winding measured with secondary winding

shorted corresponds to the primary leakage inductance.

To measure the secondary leakage inductance, connect the secondary winding

instead of the primary to the R&S LCX-Z5 and short circuit the primary winding.

Instrument functions

R&S

LCX Series

70User Manual 1179.2260.02 ─ 08

8 Instrument functions

This section includes the basic instrument functions and operating modes. You can

configure these functions, either directly with the front panel controls or in the "Mea-

surement" menu.

8.1 Measurement mode

The R&S LCX LCR meter starts and performs a measurement according to the used

measurement mode:

●

Continuous

The instrument starts the measurement and perfoms it continuously.

Using this mode enables you to collect a series of measured values, e.g. to deter-

mine value deviations of the component sample, or to determine tolerance ranges.

●

Triggered

The instrument starts a measurement cycle controlled by a trigger event.

You can initiate a trigger event on the instrument with the [Trig.], with a remote con-

trol command or you can use an externally applied trigger signal.

The external trigger inputs are always enabled and thus start a measurement when

a trigger pulse is detected on one of the inputs. Signals received at the trigger input

during a measurement cycle take no effect until the current cycle is completed.

Using the manual trigger mode, you can e.g., measure a sample component at a

series of defined working points, by switching to the working points between the

measurements.

See:

●

"Using the manual trigger mode" on page 71.

●

"Using the continuous measurement mode" on page 71

●

"Interfaces for external trigger signals" on page 71

●

"Digital trigger and control interfaces" in the specifications document for details on

the signal level and specification of the interfaces.

Status display of the [Trig.] key LED

The LED of the [Trig.] indicates the status of the triggered mode:

●

Lighting permanently (triggered)

The measurement is running. The LED turns off after the measurement.

●

Blinking (armed)

The trigger is enabled with a delay time. After the time elapses, the measurement

starts, the LED lights permanently and turns off after the measurment.

●

Off (idle)

The trigger is disabled.

The R&S LCX indicates the trigger status also in the status bar, see Table 4-7.

Measurement mode

Instrument functions

R&S

LCX Series

71User Manual 1179.2260.02 ─ 08

Interfaces for external trigger signals

You have two options to apply an external trigger signal:

●

Trigger Input connector

Assign an external trigger signal to the Trigger Input connector at the rear panel.

The rising edge of the digital signal triggers the measurement at the TTL level of

+5 V.

●

Trigger signal input of the binning interface (option: R&S LCX-K107)

The binning interface provides the digital trigger signal at pin 9 of the digital I/O

port, see Binning > Assignment of the binning interface.

The falling edge of the signal triggers the measurement.

Using the continuous measurement mode

To measure a component sample in the default continuous measurement mode:

1. If the [Meas. Mode] key at the front panel lights up, press it to switch to continuous

mode.

The R&S LCX measures continuously and updates the readings according to

selected measurement speed, see "Speed" on page 80.

2. Press the [Hold] key to keep the range setting constant.

The [Hold] key lights up. You can use the function, e.g. to measure a batch of the

same components.

3. To disable automatic range selection, press the [Hold] key again.

The key no longer lights up.

Using the manual trigger mode

This example describes the steps to be taken, for measuring a component sample at a

series of working points, triggered manually:

1. Press the [Meas. Mode] key at the front panel.

The key lights up. The R&S LCX stops the continuous measurement, switches to

triggered mode and waits for a trigger event.

2. To set a time delay between the initiated trigger and the measurment start:

a) Press the [settings] key at the front panel.

b) Select the "Measurement".

c) Select "Trigger Delay".

d) Enter the time using the keypad on the screen.

Confirm with

3. Press the home key to return to the measurement window.

4. To start the measurement, press the [Trig.] key at the front panel (Remote com-

mand: *TRG on page 185).

The key lights up. The R&S LCX performs one measurement cycle. When comple-

ted, the key turns off and the R&S LCX waits for the next trigger signal.

Measurement mode