80S-2080F480F4-680F5 User’s Manual.pdf - 第487页
9 Maintenance SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 9.3 Machine Base Ed ition 03/98 from Software Version SR.404.xx 9 - 38 9.3.9 Emp ty Tape Cutter on SIPLACE 80F 5 Automatic Pla cement Systems 9.3.9.1 Maintaining the …
SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 9 Maintenance
Edition 03/98 from Software Version SR.404.xx 9.3 Machine Base
9 - 37
9.3.8.3 Cleaning the protective covers
Clean the protective covers with a soft, dry cloth, if necessary.
Clean the protective covers with alcohol if they are very dirty.
CAUTION
• Do not use any cleaning agents other than water or ethyl alcohol to clean the protective covers.
• Only use soft cloths for cleaning.
Otherwise you will damage the EGB protective coating on the protective covers.
PLEASE NOTE:
Do not use alcohol to clean the barcode strips because they are glued on and could fall off.
9 Maintenance SIPLACE 80S-20/F4/F4-6/F5 User’s Manual
9.3 Machine Base Edition 03/98 from Software Version SR.404.xx
9 - 38
9.3.9 Empty Tape Cutter on SIPLACE 80F
5
Automatic Placement
Systems
9.3.9.1 Maintaining the Sliding Surface between the Moving Cutting Blade and
Retainer
DANGER
Switch off the automatic placement system and disconnect from the power supply.
WARNING
Disconnect the automatic placement system from the compressed air supply.
Spray the two sliding surfaces between moving cutting blade and retainer with the lubricant and corrosion
inhibiting agent WD40.
Fig. 9.3.8 Maintaining the sliding surfaces on the used tape cutter on SIPLACE 80F
5
automatic placement systems
- Key to Fig. 9.3.8
1 Moving blade
2 Retainer
A Spray the sliding surfaces with the lubricant and corrosion inhibiting agent WD40
2
A
2
A
1
SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 9 Maintenance
Edition 03/98 from Software Version SR.404.xx 9.3 Machine Base
9 - 39
9.3.9.2 Replacing the cutting edges of the fixed or moving cutting blades
DANGER
Switch off the automatic placement system and disconnect from the power supply.
WARNING
Disconnect the automatic placement systems from the compressed air supply.
If there is a wafflepack changer installed, remove it first (see Section 9.8, Page 9 - 91).
Remove the component table (see section 9.3.3.7, Page 22).
Remove the used tape channel.
PLEASE NOTE
Always replace the cutting edges of the fixed and moving cutting blades at the same time since the two cutting
blade are mechanically matched to one another.
Loosen the two M6x30 hexagon socket head screws (point 2, Fig. 9.3.9) for fixing the fixed cutting blade
Raise the blade and mark the previously used cutting edge.
Loosen the two M4x25 hexagon socket head screws (point 4, Fig. 9.3.9) for fixing the moving cutting
blades. Use an SW 10 spanner to secure the square spacer (point 5, Fig. 9.3.9) to prevent it turning.
Turn the moving cutting blade you have removed 180° about the A-B axis (point A, Fig. 9.3.9).
Fix the moving cutting blade. Use the spanner to secure the square spacer (point
ƒ
, Fig. 9.3.9) to prevent it
turning.
Turn the fixed cutting blade about the A-B axis, 180° from the original position (point B, Fig. 9.3.9).
Fix the fixed cutting blade.
Remove the used tape channel and the component table.
Reinstall the wafflepack changer, if necessary.