80S-2080F480F4-680F5 User’s Manual.pdf - 第581页
10 Component Handling SIPLACE 80 S20/F4/F4-6/F 5 User’s Manual 10.6 Wafflepack Changer Edition 03/ 98 from Software Version SR.404.xx 10 - 28
SIPLACE 80 S20/F4/F4-6/F5 User’s Manual 10 Component Handling
Edition 03/98 from Software Version SR.404.xx 10.6 Wafflepack Changer
10 - 27
Undo the clamping screws at the feet (see Fig. 10.6.5) and using a 10 mm ball socket wrench rotate the
wafflepack changer downwards until the docking pin engages. The wafflepack changer must at this point
be aligned using the machine spirit level fitted to the wafflepack changer.
Tighten up the clamping screws and check the machine spirit level again.
Reinstall the upper part of the camera on the component vision module.
10.6.10 Technical Data
Wafflepack changer
Length approx. 1475 mm
Width approx. 620 mm
Height approx. 1355 mm
Weight approx. 240 kg
Magazine size 238 mm x 338 mm
Vertical stroke 470 mm
Horizontal stroke 730 mm
Pitch 17 mm
Storage unit capacity 28 trays for holding flatpack magazines
Tray 260 mm x 360 mm
Max. weight of storage unit 50 kg
Floor load < 25N/cm²
Changeover time (magazine/magazine) ≤ 3 sec.
Tab. 10.6.1
10 Component Handling SIPLACE 80 S20/F4/F4-6/F5 User’s Manual
10.6 Wafflepack Changer Edition 03/98 from Software Version SR.404.xx
10 - 28
SIPLACE 80 S20/F4/F4-6/F5 User’s Manual 10 Component Handling
Edition 03/98 from Software Version SR.404.xx 10.7 Support for Flatpack Magazine (Manual Tray Rest)
10 - 29
10.7 Support for Flatpack Magazine (Manual Tray
Rest)
PLEASE NOTE
The manual tray holder must only be placed on the right side of the SIPLACE 80F
4
or 80F
4
-6/F
5
. The tray
holder can only be positioned so that the right edge covers no more than track 73.
10.7.1 General Information
With the support for flatpack magazines components can be picked up from individual flatpack magazines.
The flatpack magazines are changed by hand.
The support for flatpack magazines is positioned on the component table like a feeder.
There are two different versions of the support which differ in their width.
Support for large flatpack magazine (260 mm) from item No. 00116430-01
Support for small flatpack magazine (136 mm) from item No. 00116432-01
10.7.2 Installation
Insert the front side of the manual tray rest into the associated centering pin (B in Fig. 10.7.1).
Position the rear of the manual tray rest into the spherical cap on the component table (A in Fig. 10.7.1).
Make sure the manual tray rest is resting securely on the component table.
Position one side of the flatpack tray in the mounting (C in Fig. 10.7.1) and then press the other side into
the mounting (D in Fig. 10.7.1).
Slide the flatpack magazine up against the stop (E in Fig. 10.7.1).
Secure the flatpack magazine carrier by pressing the clamp downwards (F in Fig. 10.7.1).
To remove the flatpack magazine carrier press the clamp once more.
NOTE
With the "mounting for small flatpack magazine" (136 mm) a flatpack magazine (JEDEC or CENELEC flat-
pack magazines) can be fitted directly to the mounting, in other words, without a flatpack magazine carrier
being used.The clamp will however need changing.