2OM-1733-005w_F8.pdf - 第132页
2OM-1733 2-2-6 Items Ref. No. UP MOVE 1st Speed DCLR SET 2nd Speed DCLR SET V ac. Ctrl. clelayed starts V ac. Wtg. T imer Z clamp waiting time D02_09 DN MOVE 1st Speed DCLR SET 2nd Speed DCLR SET Damaged V ac. Wtg. time …
2OM-1733
2-2-5
2.4 Composition of Control Data
The set parameters are used to set the automatic operation and PCB transfer
control.
Reference
Refer to "3.4 Control" in Chapter 2, for the details of each item.
D01 Control
Table 2B2-7
Items Ref. No.
Placement Mode D01_01
PCB Finishing Position D01_02
Pre-PL cmpnt thkns
PCB Top [mm], PCB Bottom [mm]
D01_03
D02 PCB Locate
Table 2B2-8
Items Ref. No.
PCB detection off DLY D02_01
PCB Locate SET D02_02
PCB Locate Sequence D02_03
UP
MOVE
1st Speed DCLR SET
2nd Speed DCLR SET
Z Clamp
Opr. waiting time
Opr. ST DLY timer
D02_04
DN
MOVE
1st Speed DCLR SET
2nd Speed DCLR SET
Backup axis DN start DLY
D02_05
SW POSN of 1st / 2nd D02_06
Replace Vacuum Sensor D02_07
PCB Position of Contact D02_08
1403-004
2.4 Composition of Control Data
2OM-1733
2-2-6
Items Ref. No.
UP
MOVE
1st Speed DCLR SET
2nd Speed DCLR SET
Vac. Ctrl. clelayed starts
Vac. Wtg. Timer
Z clamp waiting time
D02_09
DN
MOVE
1st Speed DCLR SET
2nd Speed DCLR SET
Damaged Vac. Wtg. time
Backup axis DNstart CLY
D02_10
D03 Transfer speed
Table 2B2-9
Items Ref. No.
Transportation speed SET D03_01
Transfer speed
Carrier, Stage inside, Output
D03_02
Component Deviation Control
Carrier, Stage inside, Output
D03_03
Control the stop position
Carrier, Positioning 1, Positioning 2, Output
D03_04
1403-004
2.4 Composition of Control Data
2OM-1733
2-2-7
2.5 Composition of Placement Nozzle Data
The set parameters are used to place the nozzles onto the specied positions on
the head (Place Head/Noz No.).
Reference
Refer to "3.5 PL Head / Nozzle" for the details of each item according to the
reference Nos. (Ref. Nos.).
E01 Nozzle Place
Table 2B2-10
Items Ref. No.
Nozzle Place (E01-01)
Nozzle Stk 11 (E02)
Nozzle Stk 12 (E02)
Nozzle Stk 21 (E02)
Nozzle Stk 22 (E02)
2.6 Composition of Placement Feeder Location Data
The set parameters are used to determine which feeder slot Nos. (Fdr No.) various
types of components should be allocated to.
Component IDs (types of components to be allocated) must be specied for each
individual feeder bases.
Reference
Refer to "3.6 CMPNT PL" for the details of each item according to the reference
Nos. (Ref. Nos.).
F01 CMPNT PL
Table 2B2-11
Items Ref. No.
Fdr No. (F01_01)
Component ID (F01_02)
C (Control Command) (F01_03)
Comment (F01_04)
Feeder Fixed (F01_05)
Feeder Alternate (F01_06)
Fdr No. (F01_07)
Component Library Comment (F01_08)
Dir [deg], Carrier Data Type, Width [mm] (F01_09)
Fd. Pitch [mm] (F01_10)
Used Parts (F01_11)
Nozzle Type (F01_12)
1212-003
2.5 Composition of Placement Nozzle Data