OM-1068-001.pdf - 第10页

Contents Page 01 12-003 9 Tg0252-PM-SO 3. Component Information ................................................ Chapter 1 3- 9 4. Matrix Change Operations ............................................ Chapter 1 3- 1 1 Se…

100%1 / 273
Contents
Page
0112-003 8 Tg0252-PM-SO
6. Start Procedure of Automatic Operation ....................... Chapter 1 2-29
6.1 General Start Procedure.......................................... Chapter 1 2-29
6.2 Temporary Stop Procedure ..................................... Chapter 1 2-30
6.3 Start Procedure from “PAUSE” Mode...................... Chapter 1 2-30
7. Component Replenishment during
Automatic Operation ........................ Chapter 1 2-31
7.1 Component Replenishment in
“Component Shortage” Mode...................... Chapter 1 2-31
8. Stop Operation .............................................................. Chapter 1 2-34
8.1 General Stop Procedure .......................................... Chapter 1 2-34
8.2 Automatic Stop Procedure ....................................... Chapter 1 2-34
8.3 Emergency Stop Procedure .................................... Chapter 1 2-34
9. Interruption of Automatic Operation .............................. Chapter 1 2-35
10. Shut-Down Operation (End of Production) ................. Chapter 1 2-36
11. Others .......................................................................... Chapter 1 2-37
11.1 Operation of Multi-Layer Tray Feeder
from Main Machine Side ............... Chapter 1 2-37
11.1.1 Changing from “NEUTRAL” to “LINE” Mode .. Chapter 1 2-37
11.1.2 Zeroing Operation Maneuvered on
Main Machine Side ............... Chapter 1 2-38
11.1.2.1 Zeroing Operation Procedure
at “AUTO OPN SUB-MENU” Display .... Chapter 1 2-38
11.1.2.2 Operation Procedure
at “ZEROING OPERATION” Display .... Chapter 1 2-39
11.1.3 Tray Chuck Matrix Change Operations .......... Chapter 1 2-41
11.2 Tray Fixing Metals.................................................. Chapter 1 2-44
Section 3 LINE Mode Menu .................................................. Chapter 1 3- 1
1. LINE Mode .................................................................... Chapter 1 3- 2
2. Component Replenishment .......................................... Chapter 1 3- 4
2.1 To replenish components whenever necessary ...... Chapter 1 3- 6
2.2 Confirmation of “Component Replenishment
Completed” Mode before Machine Operation ...... Chapter 1 3- 8
Contents
Page
0112-003 9 Tg0252-PM-SO
3. Component Information ................................................ Chapter 1 3- 9
4. Matrix Change Operations ............................................ Chapter 1 3- 11
Section 4 LOCAL Mode Menu .............................................. Chapter 1 4- 1
1. LOCALMODE Display ................................................... Chapter 1 4- 2
2. Zeroing Operation ......................................................... Chapter 1 4- 3
3. MANUAL MODE Display ............................................... Chapter 1 4- 5
3.1 ELEVATOR UNIT Display ........................................ Chapter 1 4- 6
3.2 TRAVERSE UNIT Display ....................................... Chapter 1 4- 7
Chapter 2 Programming ................................. Chapter 2 1
Section 1 Offset Data............................................................ Chapter 2 1- 1
1. TRAY FEEDER OFFSET Display ................................. Chapter 2 1- 2
2. FEEDER (B) OFFSET Display ...................................... Chapter 2 1- 3
Chapter 3 Troubleshooting ......................... Chapter 3 1
Section 1 Cause and Remedy of Simple Trouble ................. Chapter 3 1- 1
1. Confirmation of Low Component
Pick-Up Rate (Handling Errors) ...................... Chapter 3 1- 2
2. Case: Power is not supplied to
the multi-layer tray feeder ........................... Chapter 3 1- 3
3. Case: Power is not supplied to the elevator shaft......... Chapter 3 1- 4
Section 2 Troubleshooting based on Error Indication ........... Chapter 3 2- 1
1. ERROR Display ............................................................ Chapter 3 2- 2
2. Remedial Procedure after Error Display ....................... Chapter 3 2- 3
Contents
Page
0112-003 10 Tg0252-PM-SO
3. Error Messages ............................................................. Chapter 3 2- 4
4. Troubleshooting after Error Message ........................... Chapter 3 2- 5
Section 3 Management Information Messages .................... Chapter 3 3- 1
1. Starting Guidance.......................................................... Chapter 3 3- 2
2. Reset Procedure after Check Message ........................ Chapter 3 3- 3
3. List of Check Messages ................................................ Chapter 3 3- 4
Section 4 Management Information ...................................... Chapter 3 4- 1
1. Machine Information ..................................................... Chapter 3 4- 2
1.1 INFO. Display .......................................................... Chapter 3 4- 2
1.2 Reset Procedure after Machine Information ........... Chapter 3 4- 3
1.3 List of Machine Information Messages ................... Chapter 3 4- 3
Chapter 4 Maintenance.................................... Chapter 4 1
Section 1 Maintenance ......................................................... Chapter 4 1- 1
1. Precautionary Items ...................................................... Chapter 4 1- 2
2. Same Types of Lubricants ............................................ Chapter 4 1- 3
3. Monthly Maintenance .................................................... Chapter 4 1- 4
4. Maintenance (Every 3 Months after Initial Month) ........ Chapter 4 1- 5
5. Detachment and Attachment of Center Cover .............. Chapter 4 1- 6
5.1 Detachment ............................................................. Chapter 4 1- 6
5.2 Attatchment ............................................................. Chapter 4 1- 6
Chapter 5 Materials .............................................. Chapter 5 1
Section 1 Material (FP-5021L) .............................................. Chapter 5 1- 1
1. Air Piping Diagram (FP-5021L) ..................................... Chapter 5 1- 2
2. Electrical Circuit Diagrams ............................................ Chapter 5 1- 3